WCH CH32V003 Series Скачать руководство пользователя страница 162

Страница: 162 / 181

CH32V003

Reference Manual

http://wch.cn

V1.3

162

Control register 2

Bit

Name

Access

Description

Reset value

[15:8] Reserved

RO Reserved

TXEIE

Tx buffer empty interrupt enable bit. Setting this
bit allows an interrupt to be generated when TXE
is set.

RXNEIE

RX buffer not empty interrupt enable bit.

Used to

generate an interrupt request when the RXNE flag
is set.

ERRIE

Error interrupt enable bit.

Setting this bit allows

interrupts to be generated when errors (CRCERR,
OVR, MODF) are generated.

[4:3]

Reserved

RO Reserved

SSOE

SS output enable bit. Disabling SS output can
work in multi-master mode.
1: Enable the SS output.
0: Disable SS output in Master mode.

TXDMAEN

Tx buffer DMA enable bit.
1

：

Enable Tx buffer DMA.

：

Disable Tx buffer DMA.

RXDMAEN

Rx buffer DMA enable bit.
1

：

Enable Rx buffer DMA.

：

Disable Rx buffer DMA.

14.3.3 SPI Status register (SPI1_STATR)

Offset address: 0x08

Reserved

BSY OVR MODF CRC

ERR UDR CHSID TXE RXNE

Bit

Name

Access

Description

Reset value

[15:8] Reserved

RO Reserved

BSY

Busy flag.

This flag is set and cleared by

hardware.
1

：

SPI is busy in communication or Tx buffer is

not empty.
0

：

SPI (or I

S) not busy.

OVR

RWO

Overrun flag.

This flag is set by hardware and

reset by a software sequence.
1

：

Overrun occurred.

：

No overrun occurred.

MODF

Mode fault.

This flag is set by hardware and reset

by a software sequence.
1

：

Mode fault occurred.

：

No mode fault occurred.

CRCERR

RW0

CRC error flag.

This flag is set by hardware and

reset by a software sequence.
1

：

CRC value received does not match the

SPI_RXCRCR value.
0

：

CRC

value

received

matches

the

SPI_RXCRCR value.

UDR

Underrun flag.

This flag is set by hardware and

reset by a software sequence.
1

：

Underrun occurred.

：

No underrun occurred.

Содержание CH32V003 Series






















































































































































































Результаты поиска

Содержание CH32V003 Series

Отзывы:

Бренды по названию

Популярные бренды

WCH CH32V003 Series, Справочное руководство

Результаты поиска

Содержание CH32V003 Series

Отзывы:

Бренды по названию

Популярные бренды