WCH CH32V003 Series Скачать руководство пользователя страница 154 | Manualshive

Страница: 154 / 181

WCH CH32V003 Series Скачать руководство пользователя страница 154

CH32V003

Reference Manual

V1.3

154

received byte will be lost; when in send mode, no
new data is written to the data register, and the
same byte will be sent twice.
0: No overrun or underrun events.

10

AF

RW0

Acknowledge failure bit.

Cleared by software

writing 0, or by hardware when PE=0.
1

：

Acknowledge failure.

0

：

No acknowledge failure.

0

9

ARLO

RW0

Arbitration lost bit.

Cleared by software writing

0, or by hardware when PE=0.
1

：

Arbitration Lost detected.

0

：

No Arbitration Lost detected.

0

8

BERR

RW0

Bus error bit. Cleared by software writing 0, or by
hardware when PE=0.
1

：

No misplaced Start or Stop condition.

0

：

No misplaced Start or Stop condition.

0

7

TxE

RO

Data register empty bit.

Cleared by software

writing to the DR register or by hardware after a
start or a stop condition or when PE=0.
1

：

Data register empty.

0

：

Data register not empty.

0

6

RxNE

RO

Data register not empty bit.

Cleared by software

reading or writing the DR register or by hardware
when PE=0.
1

：

Data register not empty.

0

：

Data register empty.

0

5

Reserved

RO Reserved

0

4

STOPF

RO

Stop detection bit.

Cleared by software reading

the SR1 register followed by a write in the CR1
register, or by hardware when PE=0
1

：

Set by hardware when a Stop condition is

detected on the bus by the slave after an
acknowledge (if ACK=1).
0

：

No Stop condition detected.

0

3

ADD10

RO

10-bit header sent bit.

Cleared by software

reading the SR1 register followed by a write in the
DR register of the second address byte, or by
hardware when PE=0.
1

：

Master has sent first address byte.

0

：

No ADD10 event occurred.

0

2

BTF

RO

Byte transfer finished bit.

Cleared by software

reading SR1 followed by either a read or write in
the DR register or by hardware after a start or a
stop condition in transmission or when PE=0.
1

：

Data byte transfer succeeded.

When

NOSTRETCH=0: when sending, when a new data
is sent and the data register has not yet been
written with new data; when receiving, when a
new byte is received but the data register has not
yet been read.
0

：

Data byte transfer not done.

0

1

ADDR

RW0

Address sent /matched bit.

This bit is cleared by

software reading SR1 register followed reading
SR2, or by hardware when PE=0.
In Master mode:
1

：

End of address transmission.

For 10-bit

addressing, the bit is set after the ACK of the 2nd

0

«
...
152
153
154
155
156
...
»

Содержание CH32V003 Series






















































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды