Waync Dalton 9100 страница 6 Скачать руководство пользователя

Страница: 6 / 40

Tools Needed:

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the

Find a Dealer

section online at

www.wayne-dalton.com

faIluRE TO usE aPPROVED

WINDING BaRs CaN CausE

sPRING ENERGy TO BE RElEasED

suDDENly, REsulTING IN sEVERE

OR faTal INjuRy.

COuNTERBalaNCE sPRING

TENsION MusT BE RElIEVED

BEfORE REMOVING aNy

haRDWaRE. a POWERful

sPRING RElEasING IT’s ENERGy

suDDENly CaN CausE sEVERE OR

faTal INjuRy.

Do not release the torsion spring tension

unless you are qualified and experienced

door technician, but have a professional

door agency release the tension.

Step 1:

Close the door and place vice

clamps to the back legs on both vertical

tracks, above the third roller to prevent

the door from lifting as you unwind the

springs. use only approved winding bars

available from your dealer. Do not use

undersized steel rods, screw drivers or

anything else to unwind the springs.

Position the ladder just off to the side

of the winding cone. The winding cone

should be easy to reach without putting

your body directly in front of it.

Step 2:

Insert a winding bar into one

of the holes in the winding cone. Exert

upward pressure. using caution, loosen

the two (2) set screws in the winding

cone. Be prepared to support the full

torsional force of the spring when the set

screws are loosened.

Step 3:

Once set screws are loose, slowly

and carefully lower the winding rod until it

rests against the door. Insert other winding

bar into the upper hole. Push up and

remove lower bar. Carefully lower upper

winding bar until it rests against the door.

Repeat process until all tension is relieved.

If your door is equipped with two (2)

torsion springs, follow the same procedure

to relieve tension on the second spring.

Step 4:

Remove vice clamps from tracks,

unbolt torsion shaft assembly and remove

from work area.

NOTE:

Continue with “P4” on page 9 after

completing this step.

Torsion Spring Removal

For Standard lift

aPPROVED WINDING BaR

TORsION assEMBly

WINDING CONE

sET sCREWs

fIRMly hOlD WINDING BaRs aND

CauTIOusly lOOsEN sET sCREWs

wARNINg

approved

Winding Bars

3/8” Wrench

Vice Clamp

Recommended

tools from

page 5

Содержание 9100









































Результаты поиска

Содержание 9100

Отзывы:

Похожие инструкции для 9100

Бренды по названию

Популярные бренды

Waync Dalton 9100, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 9100

Отзывы:

Похожие инструкции для 9100

Бренды по названию

Популярные бренды