Waync Dalton 9100 Скачать руководство пользователя страница 2

2

Please Do Not Return This Product To The Store. 

Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your 

local yellow pages/business listings or go to the 

Find a Dealer

 section online at 

www.wayne-dalton.com

Definition of key words used in this manual:         

INDICaTEs a POTENTIally hazaRDOus 

sITuaTION WhICh, If NOT aVOIDED, COulD 

REsulT IN sEVERE OR faTal INjuRy.

CAUTION:

 PROPERTy DaMaGE OR INjuRy CaN REsulT 

fROM faIluRE TO fOllOW INsTRuCTIONs.

IMPORTANT:

 REquIRED sTEP fOR safE aND PROPER 

DOOR OPERaTION.

NOTE:

 Information assuring proper installation of the door.

READ ThESE 

INSTRUCTIONS CAREFUlly bEFORE 

ATTEMPTINg INSTAllATION. IF 

IN qUESTION AbOUT ANy OF ThE 

PROCEDURES, DO NOT PERFORM ThE 

wORk. INSTEAD, hAvE A qUAlIFIED 

DOOR AgENCy DO ThE INSTAllATION 

OR REPAIRS.

1. 

READ AND FOllOw All INSTAllATION INSTRUCTIONS.

2.  Wear protective gloves during installation to avoid possible 

 

cuts from sharp metal edges.

3.  It is always recommended to wear eye protection when using 

 

tools, otherwise eye injury could result.

4.  avoid installing your new door on windy days. Door could 

 

fall during the installation causing severe or fatal injury. 

5.  Doors 12’-0” wide and over should be installed by two 

 

persons, to avoid possible injury. 

6.  Operate door ONly when it is properly adjusted and free from 

 

obstructions.

7.  If a door becomes hard to operate, inoperative or is damaged, 

 

immediately have necessary adjustments and/or repairs 

 

made by a trained door system technician using proper tools 

 

and instructions.

8.  DO NOT stand or walk under a moving door, or permit 

 

anybody to stand or walk under an electrically operated door.

9.  DO NOT place fingers or hands into open section joints when 

 

closing a door. use lift handles/gripping points when operating 

 

door manually.

10.  DO NOT permit children to operate garage door or door 

 

controls. severe or fatal injury could result, should the child  

 

become entrapped between the door and the floor. 

11.  Due to constant extreme spring tension, DO NOT attempt any 

 

adjustment, repair or alteration to any part of the door, 

 

especially to springs, spring brackets, bottom corner brackets, 

 

red colored fasteners, cables or supports. To avoid possible 

 

severe or fatal injury, have any such work performed 

 

by a trained door systems technician using proper tools and 

 

instructions.

12.  On electrically operated doors, pull down ropes must be 

 

removed and locks must be removed or made inoperative in 

 

the open (unlocked) position.

13.  Top section of door may need to be reinforced when attaching 

 

an electric opener. Check door and/or opener manufacturer’s 

 

instructions.

14.  VIsually inspect door and hardware monthly for worn and or 

 

broken parts. Check to ensure door operates freely.

15.  Test electric opener’s safety features monthly, following 

 

opener manufacturer’s instructions.

16.  NEVER hang tools, bicycles, hoses, clothing or anything else 

 

from horizontal tracks. Track systems are not intended or 

 

designed to support extra weight.

 

After installation is complete, fasten this manual 

near garage door. 

Table of Contents                                                   

Important safety Instructions .................................................. 2
Package Contents ................................................................... 3
Door section Identification ...................................................... 4
Tools Required ........................................................................ 5

Pre-Installation ..................................................................5-10
 

Removing The Old Door .......................................5-9

 

Preparing The Opening ......................................... 10

Installation  ......................................................................11-31

Optional Installations .......................................................32-36
 

side lock ............................................................. 32

 

Doormaster

TM

 Bracket

 ......................................... 32

 

step Plate ............................................................. 33 

 

Pull Rope .............................................................. 33

 

Trolley Instructions for standard lift ..................... 34 

 

Trolley Instructions for low headroom ................. 35 

 

Trolley Operator .................................................... 36

Maintenance ....................................................................37-38
 

Cleaning ............................................................... 37

 

Painting Instructions ........................................37-38

Warranty ............................................................................... 39

Dealer locator Information.................................................... 40

wARNINg

wARNINg

Содержание 9100









































Отзывы: