13
Tools Needed:
Tools Needed:
Please Do Not Return This Product To The Store.
Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer
section online at
www.wayne-dalton.com
INST
All
ATION
Measure the length of the vertical tracks.
using the jamb bracket schedule,
determine the placement of the jamb
brackets for your door height and track
type. To install the jamb brackets,
align the twistlock tab on the quick
install jamb bracket with the quick
install feature in the track and turn the
bracket perpendicular to the track so the
mounting flange is toward the back (flat)
leg of the track.
Installing q.I. Jamb brackets
TOP
hOlE
BOTTOM
hOlE
MIDDlE
hOlE
JAMb bRACkET SChEDUlE
DOOR
hEIghT
1ST SET
2ND SET
3RD SET
JAMb bkT
POSITION
JAMb bkT
POSITION
JAMb bkT
POSITION
6’0” 64” TRACk
(1626 mm)
qIjB - 5
MIDDlE
qIjB - 6
BOTTOM
NOT aPPlICaBlE
6’5” 69” TRACk
(1753 mm)
qIjB - 3
BOTTOM
qIjB - 6
MIDDlE
NOT aPPlICaBlE
6’8” 72” TRACk
(1829 mm)
qIjB - 3
BOTTOM
qIjB - 6
MIDDlE
NOT aPPlICaBlE
7’0” 76” TRACk
(1930 mm)
qIjB - 3
BOTTOM
qIjB - 7
TOP
NOT aPPlICaBlE
7’3” 79” TRACk
(2007 mm)
qIjB - 3
BOTTOM
qIjB - 5
BOTTOM
qIjB - 6
BOTTOM
7’6” 82” TRACk
(2083 mm)
qIjB - 3
BOTTOM
qIjB - 5
BOTTOM
qIjB - 6
BOTTOM
7’9” 85” TRACk
(2159 mm)
qIjB - 3
BOTTOM
qIjB - 5
BOTTOM
qIjB - 6
BOTTOM
8’0” 4 SECTIONS
88” TRACk (2235 mm)
qIjB - 3
MIDDlE
qIjB - 6
TOP
qIjB - 7
MIDDlE
8’0” 5 SECTIONS
88” TRACk (2235)
qIjB - 3
BOTTOM
qIjB - 7
TOP
qIjB - 8
TOP
3RD sET hOlEs
2ND sET hOlEs
1sT sET hOlEs
None
4
Drums
IMPORTANT:
RIGhT aND lEfT haND Is
alWays DETERMINED fROM INsIDE ThE
BuIlDING lOOkING OuT.
NOTE:
for door section identification see
page 4.
TorqueMaster
®
counterbalance drums
are marked right and left hand. uncoil the
counterbalance cables and make sure you
place the right hand cable loop on the right
hand milford pin and place the left hand
cable loop on the left hand milford pin.
Insert a roller into bottom bracket of the
bottom section and insert another roller
at #1 end hinge at the top of the bottom
section. Repeat for other side.
NOTE:
Verify astragal (bottom seal) is
aligned with door section. If there is more
than 1/2” excess astragal on either side,
trim astragal even with door section.
None
lEfT haND TORquEMasTER
®
COuNTERBalaNCE DRuM
BOTTOM
sECTION
MIlfORD PIN
#1 END hINGE
(hINGE TuBE)
BOTTOM BRaCkET
BOTTOM
sECTION
asTRaGal
5
quICk INsTall fEaTuRE
qI jaMB BRaCkET
TWIsTlOCk TaB
lEfT sIDE shOWN
RIGhT sIDE shOWN
COuNTERBalaNCE
CaBlE
ROllERs
BOTTOM
sECTION
