Waync Dalton 9100 страница 20 Скачать руководство пользователя

Страница: 20 / 40

Tools Needed:

Please Do Not Return This Product To The Store.

Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the

Find a Dealer

section online at

www.wayne-dalton.com

TorqueMaster

Spring Tube

TorqueMaster

springs come lubricated

and pre-assembled inside the
TorqueMaster

spring tube. To install, lay

the TorqueMaster

spring tube on the

floor (inside garage) in front of the door
with the labeled end to the left.

laBElED END

TORquEMasTER

sPRING TuBE

None

Center bracket bushing

NOTE:

If you are installing the

drive

opener on your garage door, skip this
step and continue with step 19.

NOTE:

If you are not installing the

drive

opener on your garage door, you

must install the center bracket bushing
assembly. follow these instructions for
non-

drive

operated garage doors.

NOTE:

If you are installing a

DoorMaster

™

opener, see optional

DoorMaster

™

Bracket installations on

page 32, figure a.

Being cam shaped the center bracket
bushing only fits one way.
slide the center bracket assembly
towards the center of the TorqueMaster

spring tube, from the right side as
shown.

NOTE:

upon completion of this step,

continue with step 20.

CENTER

BRaCkET

assEMBly

TORquEMasTER

sPRING TuBE

TORquEMasTER

sPRING TuBE

CENTER

BRaCkET

BushING

Содержание 9100









































Результаты поиска

Содержание 9100

Отзывы:

Похожие инструкции для 9100

Бренды по названию

Популярные бренды

Waync Dalton 9100, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание 9100

Отзывы:

Похожие инструкции для 9100

Бренды по названию

Популярные бренды