manualshive.com logo in svg

Waygate Technologies Everest Mentor Visual iQ VideoProbe, Руководство по эксплуатации

Поделиться
Скачать
Waygate Technologies Everest Mentor Visual iQ VideoProbe Скачать руководство пользователя страница 77

77

Troubleshooting Measurements 

3D Phase, 3D Stereo, or Stereo Measurements

•  Move the probe tip as close as possible to the target, maximizing magnification.
•  Verify that the OTA len is clean and is threaded on to the probe head securely.
•  Measure the target contained in the verification block to ensure that no tip damage has occurred. 

Click here to learn more about Verifying Measurement 

OTA's.

•   Verify that the serial number engraved on the OTA matches the serial number selected in the software for measurement. 
•  Activate the zoom window to most accurately place the measurement cursors.

3D Phase Measurements

•  Be sure to hold the probe still for approximately one second during the surface scan. Do not move the probe until after the Capturing Images message  

     disappears.

•   Position the probe tip as close as possible. It is acceptable to be slightly out of focus for very small indications.
•  Make sure all measurement-tip surfaces are clean. Wipe with a clean cloth and alcohol.
•  Check point cloud view for excessive waviness or ripple, which would indicate dirt or oil contamination or tip damage.
•  Try a non-perpendicular view, such as 30-45°. This often significantly decreases the noise level in the data, especially for surfaces that are shiny or  

     have a speckled appearance.
•  Ensure that ambient light is not present on the target while capturing the 3D Phase image.

3D Stereo and Stereo Measurements

•  Avoid placing cursors in areas of significant glare. If necessary, adjust the Brightness, HDR, and/or Dark Boost. Repositioning the probe tip to enhance 

details and reduce glare may be required.
•  Verify that the object to be measured is near the center of the screen, with as much magnification as possible while still being in focus.
•  Review guidelines under 

Achieving a Suitable Image for Making Stereo Measurements

•   Verify that the matching cursor is correct within 1 pixel. If you cannot clearly see where the match point should be, select a different point, or capture 

the image from a different angle that better reveals details to allow better matching.

Содержание Everest Mentor Visual iQ VideoProbe





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды