Wavetek 3HRV Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 104

background image

4-41

Press the

TILT

soft key to turn tilt compensation on or off. Tilt

channels must be programmed in the Channel Plan Edit mode,
before this function can be implemented. The tilt is based on the
levels of the highest and lowest channels configured for tilt.

When turned on, the compensation value can be adjusted using the

UP

and

DOWN

arrow keys or by entering a numeric value followed

by the

ENTER

key. When tilt compensation is in effect, a "TILT

ON" indicator appears in the upper left portion of the scan screen.

Tilt Compensation

The tilt compensation feature allows the user to enter the cable loss
for a particular section of line and then using the scan display adjust
the gain of the amplifier to compensate for this loss.

Scan Rate

Two scan rates are available in the Scan mode, normal and fast. The
scan rate is selected in the Measurement Setup menu. The Fast scan
feature allows for rapid scan displays, while sacrificing accuracy (as
much as 2 dB on scrambled channels). Normal scan rate is slower, but
much more accurate. An indicator appears in the upper left hand
corner of the Scan screen when the Fast Scan mode is selected.

Audio Carriers

If desired, the audio carriers can be omitted resulting in a faster scan.
This feature is selected in the Measurement Setup menu. An
indicator appears in the upper left hand corner of the Scan screen
when audio carriers are omitted.

Limits

The Limits feature allows for comparison of the current scan mea-
surement with the "FCC" limits that are defined in Setup. There are
two parts to this feature.

«
...
62
63
64
65
66
...
»

Содержание 3HRV









































































































Отзывы:

Нет отзывов

Похожие инструкции для 3HRV

Бренд: Takstar Страницы: 24

Бренд: R&S Страницы: 232

Бренд: Aiwa Страницы: 33

Бренд: Alpine Страницы: 48

Бренд: Soundstream Страницы: 31

Бренд: Boss Audio Systems Страницы: 12

Бренд: Alpine Страницы: 78

Бренд: EisSound Страницы: 5

Бренд: Onkyo Страницы: 99

Бренд: Integra Страницы: 48

Бренд: Lanzar Страницы: 8

Бренд: Xantech Страницы: 3

FT-450 - CAT OPERATION REFERENCE BOOK

Бренд: Yaesu Страницы: 18

Бренд: Aquatic Страницы: 22

Бренд: National Страницы: 25

Бренд: Integra Страницы: 96

MusicFly i-Select

Бренд: DNT Страницы: 48

EL-4KHDBT-RX-40-IRS

Бренд: Elan Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды