Wavetek 3HRV Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 104

background image

4-48

Level Adjustments

A

LVL

(level) soft key is used to adjust the vertical parameters of the

graph. These parameters include Max Hold, Ref Level and Scale.

The Max Hold function ensures that the highest signal over multiple
sweeps is displayed. When the Max Hold soft key is pressed, as
indicated in the left hand corner of the display, the highest signal
level is displayed. The M1/M2 readings correspond to the max hold
levels. As multiple sweeps are performed, the maximum level trace
will only change if new sweep levels exceed the existing levels.

The reference level is located at the top line of the graph. The Ref
Level can be adjusted using the cursor keys or by entering a numeric
value followed by the enter key.

The scale parameter (1,2,5, & 10 dB/Div) can only be adjusted with
the cursor keys. For example, if the reference level was set at 0 dB
and the scale was set at 10 dB/div the first horizontal grid line above
the center would be equal to -30 dB. Press the

LVL

soft key to return

to the main spectrum analyzer display.

Frequency Adjustments

Press the

FRQ

soft key to edit frequency range parameters of the

Spectrum Analyzer display. Use the

UP

and

DOWN

arrow keys or

the numeric entry keypad to set the center frequency. Press the

Span

soft key to adjust the span frequency. The

Full Span

soft key can be

used to set the start and stop frequency to the full range of the unit.
Press the

FRQ

soft key to return to the main spectrum analyzer

display.

«
...
69
70
71
72
73
...
»

Содержание 3HRV









































































































Отзывы:

Нет отзывов

Похожие инструкции для 3HRV

Бренд: Sagem Страницы: 3

Бренд: Masterplug Страницы: 2

Бренд: Lanzar Страницы: 15

Бренд: Icom Страницы: 116

TracVision DIRECTV

Бренд: KVH Industries Страницы: 127

Бренд: Planet Audio Страницы: 16

Бренд: Xtrons Страницы: 14

Бренд: B&K Страницы: 88

Бренд: jotron Страницы: 32

DIGITAL TO TV DT-301

Бренд: Promax Страницы: 4

LAS VEGAS 7 645 650 310

Бренд: Blaupunkt Страницы: 72

Бренд: Orava Страницы: 10

Бренд: Aiwa Страницы: 33

Бренд: Eclipse Страницы: 141

Бренд: Nakamichi Страницы: 13

Бренд: FTE Maximal Страницы: 38

Бренд: CYP Страницы: 24

Бренд: Datacom Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды