Watts Premier RO-PURE, Инструкция по установке, эксплуатации и обслуживанию

Страница: 7 / 16

7
Step E – Measure the
3
⁄
8
" black tube from faucet to the drain
saddle on the drain pipe and make a straight cut to the
correct length.
Step F – Connect the black tube to the open quick connect fi tting
on the drain saddle by pushing the tube all the way to the
tube stop.
STEP 8
Green Tube Connection
Step A –
Locate green tube attached to the
RO Module. Insert the open end of
the green
1
⁄
4
" tube into the open
1
⁄
4
"
quick connect fi tting on the plastic
Adapt-A-Valve™ valve making sure
the tube is pushed in all the way to
the tube stop.
STEP 9
Tank Ball Valve Installation
Step A – Tefl on tape must be applied in a
clockwise direction. Wrap (7 to 12
turns) around the male pipe threads
(MPT) on the stainless steel fi tting on
top of the tank.
NOTICE
Do not over-tighten.
Step A – Thread the quick connect ball valve
(supplied in the parts bag), by hand,
onto the stainless steel connector
on the tank.
STEP 10
Blue Tube Connection To Tank
Step A –
Position tank in desired location. Stand it upright or lay it
on its side (using the black plastic stand). Measure the blue
tube (marked “TANK”) from the RO module to the tank and
cut it to length leaving a straight, square edge. Insert the
tube into the quick connect fi tting on the tank ball valve.
Make sure the tube is pushed in all the way to the tube
stop (see page 4 for quick connect fi tting use directions).
7-12 TURNS
STEP 11
Ice maker Connection
Step A – If you have a refrigerator / ice maker that you would like to
connect to your RO system, you can connect that to the
blue tube (purifi ed water) leading to the RO faucet.
NOTICE
A connection from the RO to the refrigerator / ice maker system
must have an in-line valve installed in-between so it can easily be
closed to prevent water fl owing to the ice maker during start up
and periodic maintenance. An Ice maker Connection Kit can be
purchased through Premier.
Startup
NOTICE
If your RO system is connected to a refrigerator / ice maker,
you must turn off the connection to that appliance during the
system startup.
Do not re-open the connection until after the system has
been completely fl ushed (as described below) and the tank is
allowed to fi ll up completely in order for the appliance to
work properly.
Discard the fi rst batch of water or ice made from the RO
water after startup.
Step A –
Turn on the water supply at both
the cold water supply valve and
Adapt-A-Valve™. Check the
system for leaks and tighten any
fi ttings as necessary. (Continue to
check frequently over the next 24
hours to ensure no leaks
are present).
Step B – Open the RO faucet and leave it open until water begins to
trickle out (this may take a few minutes and the water will
come out slowly).
Step C – Close the RO faucet allowing the storage tank to fi ll with
water. It may take 3 to 6 hours to fi ll the tank completely
depending on the production capability of the membrane,
local water temperature and water pressure.
NOTE: During the fi ll period you may hear water trickling
which is a normal occurrence.
Step D – After the storage tank is full, open the RO Faucet to fl ush
the tank completely. You will know that the tank is empty
when the fl ow rate from the RO faucet is down to a trickle.
Repeat this step two more times. The fourth tank can be
used for drinking.
NOTE: The fl ushing process should take about a day
to complete.
NOTE: Flushing of the tank 3 times is only necessary
during the initial startup and after replacing
the membrane.
NOTICE
Check frequently over the next 24 hours to ensure no leaks
are present.
OFF
ON
1/4”
GREEN TUBE
IOM-Premier-RO-PURE.indd 7 7/10/20 2:32 PM