manualshive.com logo in svg

WattAge egret, Инструкция по сборке

Поделиться
Скачать
WattAge egret Скачать руководство пользователя страница 33

33

❑

10) Double check the gear mesh.  If you are sat-

isfied that it is correct, apply a couple of drops of
Trinity bushing oil onto the gear box bushings.  Also
apply a light coating of grease to the gears and rotate
the prop shaft a couple of times to distribute the oil
and grease.

❑

11) Remove any excess oil using a paper towel

and reinstall the motor.  Hook up the motor leads to
the ESC and mount the propeller adapter, cowl and
propeller.

NOTES

______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________

______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________
______________________________________

Содержание egret





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды