Watlow Ez-Zone PM3 Скачать руководство пользователя страница 18

Страница: 18 / 32

PM3/PM6 LEGACY™ Express PID Controller • 18 •

Operations Menu

Display

Parameter Name Description

[`AUt]

[ AUt]

Autotune

Start an autotune. While active the
upper or left and lower or right dis-
play will flash [tUn1] and [Attn].

Appears if: Heat or cool algorithm
set to PID
Range: Defaults are shown below
in bold

[``no]

[`yES]

Yes

[`C;M]

[ C.M]

Control Mode Active

View the current control mode.

Appears if: Always
Range: (Defaults are shown in bold)

[`off]

Off

[AUto]

Auto

[MAn]

Manual

[`h;Pb]

[ h.Pb]

Heat Proportional Band

Set the PID proportional band for the
heat outputs.

Appears if: Heat algorithm set to PID
Range: (Defaults are shown in bold)
0 to 9,999.000°F or units
0 to 5,555.000°C

Units, 25.0°F or 14.0°C

[`C;Pb]

[ C.Pb]

Cool Proportional Band

Set the PID proportional band for the
cool outputs.

Appears if: Cool algorithm set to PID-
Range (Defaults are shown in bold)
0 to 9,999.000°F or units
0 to 5,555.000°C

Units, 25.0°F or 14.0°C

OPERATION MENU

Upon power up of the control, using the
advance key will scroll through the various
prompts found in the Operations Menu.
At any point within the Operations menu
to return to the default display push the
Infinity ˆ key.

Operations Menu

‰

[````]

PAr1

[````]

PAr2

[`AUt]

Autotune

[`C;M]

Control Mode

[`h;pb]

Heat Proportional Band

[`C;pb]

Cool Proportional Band

[``ti]

Time Integral

[``td]

Time Derivative

[o;tb1]

Time Base

[o;tb2]

Time Base

[`A;lo]

Alarm Low Set Point

[`A;hi]

Alarm High Set Point

[`i;Ca]

Calibration Offset

[btth]

Bluetooth

Содержание Ez-Zone PM3

































Результаты поиска

Содержание Ez-Zone PM3

Отзывы:

Похожие инструкции для Ez-Zone PM3

Бренды по названию

Популярные бренды

Watlow Ez-Zone PM3, Руководство пользователя

Результаты поиска

Содержание Ez-Zone PM3

Отзывы:

Похожие инструкции для Ez-Zone PM3

Бренды по названию

Популярные бренды