Watlow Ez-Zone PM3 Скачать руководство пользователя страница 23

Страница: 23 / 32

PM3/PM6 LEGACY™ Express PID Controller • 23 •

Setup Menu

‰

[`loC]

Lockout Menu

[`SEn]

Sensor Type

[`Lin]

Linearization

[`deC]

Decimal

[`C_F]

Display Units

[`r;lo]

Range Low

[`r;hi]

Range High

[`fn1]

Function Output 1

[`o;ty]

Output Type

[`fn2]

Function Output 2

[`h;ag]

Heat Algorithm

[`h;sC]

Hysteresis (Heat & Cool)

[`C;Ag]

Cool Algorithm

[`A;ty]

Alarm Type

[`A;hy]

Alarm Hysteresis

[`A;lg]

Alarm Logic

[`A;lA]

Alarm Latching

[`A;bl]

Alarm Blocking

[`A;si]

Alarm Silencing

[A;dsp]

Alarm Display

[``rp]

Ramp Action

[`r;rt]

Ramp Rate

[`s;lo]

Scale Low

[`s;hi]

Scale High

[o;hi1]

Power Scale High Output 1

[o;hi2]

Power Scale High Output 2

[`Ad;s]

Zone Address

[btth]

Bluetooth

SET UP MENU (Continued)

To enter the Setup Menu push and hold the
up and down arrow keys for approximately 3
seconds. Push the green advance key to scroll
through to the prompt of choice. Use the up
and down arrow keys to change the range.

Setup Menu (cont.)

Display

Parameter Name Description

[`fn2]

[ fn2]

Function of Output 2

Select which function will drive this

output.
Appears if: If output 2 is ordered

Range (Defaults are shown in bold)

[`oFF]

Off,

[CooL]

Cool,

[hEAt]

Heat,

[ALM]

Alarm

[`h;Ag]

[ h.Ag]

Heat Algorithm

Set the heat control method.
Appears if: Output 1 or 2 set to heat
Range (Defaults are shown in bold)

[`oFF]

Off,

[`Pid]

PID

[on;of]

On-Off

[`hSC]

[ hSC]

Hysteresis (Heat & Cool)

Set the control switching hysteresis for

on-off control. This determines how

far into the “on” region the process

value needs to move before the output

turns on.

Appears if: Heat or Cool Algorithm is

set to On-Off.

Range (Defaults are shown in bold)

to 9,999.000°F or units

0 to 5,555.000°C

Units, 3.0°F or 2.0°C

[`C;Ag]

[ C.Ag]

Cool Algorithm

Set the cool control method.
Appears if: If Output 1 or 2 is set

to cool
Range (Defaults are shown in bold)

[`oFF]

Off,

[

`Pid]

PID

[on;of]

On-Off

[`A;ty]

[ A.ty]

Alarm Type

Selects whether the Alarm will be a

Process Alarm/Absolute Tempera-

ture; or a Deviation Alarm/Tempera-

ture with respect to Setpoint.
Appears if: Always
Range (Defaults are shown in bold)

[`oFF]

Off,

[PR;AL]

Process Alarm

[dE;AL]

Deviation Alarm

Setup Menu

Содержание Ez-Zone PM3

































Результаты поиска

Содержание Ez-Zone PM3

Отзывы:

Похожие инструкции для Ez-Zone PM3

Бренды по названию

Популярные бренды

Watlow Ez-Zone PM3, Руководство пользователя

Результаты поиска

Содержание Ez-Zone PM3

Отзывы:

Похожие инструкции для Ez-Zone PM3

Бренды по названию

Популярные бренды