Watlow Ez-Zone PM3 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 32

background image

PM3/PM6 LEGACY™ Express PID Controller • 20 •

Setup Menu

[`A;Lo]

[ A.Lo]

Alarm Low Set Point

Process - set the process value that

will trigger a low alarm.

Deviation - set the span of units

(Must be negative number) from the
closed loop set point that will trig-
ger a low alarm.

Appears if: If Alarm Type [`A;ty] is set
to Process or Deviation Alarm
Range (Defaults are shown in bold)
-1,999.000 to 9,999.000°F or units
-1,128.000 to 5,537.000°C

Units, 32.0°F or 0.0°C

[`A;hi]

[ A.hi]

Alarm High Set Point

Process - set the process value that

will trigger a high alarm.

Deviation - set the span of units from

the closed loop set point that will
trigger a high alarm.

Appears if: If Alarm Type (A.ty) is set
to Process or Deviation Alarm
Range (Defaults are shown in bold)
-1,999.000 to 9,999.000°F or units
-1,128.000 to 5,537.000°C

Units, 300.0°F or 150.0°C

[`i;CA]

[ i.CA]

Calibration Offset

Set an offset value for a process
output.

Appears if: Always
Range (Defaults are shown in bold)

[

-1,999.000 to 9,999.000°F or units,

-1,110.555 to 5,555.000°C,

0.0

OPERATION MENU (Continued)

Upon power up of the control, using the
advance key will scroll through the various
prompts found in the Operations Menu. At any
point within the Operations menu to return to
the default display push the Infinity ˆ key.

[````]

PAr1

[````]

PAr2

[`AUt]

Autotune

[`C;M]

Control Mode

[`h;pb]

Heat Proportional Band

[`C;pb]

Cool Proportional Band

[``ti]

Time Integral

[``td]

Time Derivative

[o;tb1]

Time Base

[o;tb2]

Time Base

[`A;lo]

Alarm Low Set Point

[`A;hi]

Alarm High Set Point

[`i;Ca]

Calibration Offset

‰

Operations Menu

«
...
18
19
20
21
22
...
»

Содержание Ez-Zone PM3

































Отзывы:

Нет отзывов

Похожие инструкции для Ez-Zone PM3

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: wattio Страницы: 20

Бренд: Babybee Страницы: 28

Бренд: Taie Страницы: 66

Бренд: Baby Trend Страницы: 8

Бренд: Baby Trend Страницы: 19

Бренд: Baby Trend Страницы: 5

Бренд: Baby Trend Страницы: 4

Бренд: Rane Страницы: 2

Бренд: Samson Страницы: 20

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: Patron Страницы: 17

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды