background image

 

WL250

 Manual 

                                                      Page 65 ‐ Revision: 12‐12‐2018 

HOT TANK DESCALING INSTRUCTIONS

 

 

The hot tank requires removal of mineral deposits (descaling) on a regular basis.  Typically 
descaling should take place every 6 to 12 months to preserve the long‐term health of your 
unit.  
 
Use non‐toxic cleaner such as ScaleKleen, DEZCAL, 20% Citric Acid Solution, or Undiluted 
Vinegar Solution to remove mineral deposits as directed by the manufacturer depending 
upon filtration and local water conditions.   
 
Descaling is an important process that removes calcium deposits, or scale, that can build up 
inside a tank over time.  Calcium and scale is non‐toxic but left unattended will hinder your 
unit’s performance.  

 

 

WARNING!  

PERSONAL PROTECTIVE EQUIPMENT REQUIRED.  

Always ensure proper 

ventilation and use rubber or nitrile gloves and eye protection when using chemicals.  
Refer to Material Safety Data Sheet for specific requirements of each product.

     

 

             CAUTION!

  

 STAINLESS STEEL TANK DESCALING

.  

 

The Hot Tank is made from stainless steel.  Ensure descaling solution is compatible with 
stainless and always flush the unit completely.  Dispose in an environmentally safe 
manner. 

 

Materials Needed:  

 

Personal Protective Equipment.  Rubber or Nitrile Safety Gloves and Protective Eyewear  

 

Phillips Screwdriver   

 

Temperature Gauge 

 

Water Pitcher or Container to collect water from the faucet 

 

5‐gallon container or drain basin 

 

Citric Acid Based Cleaner 

 

¼” Plastic Tubing, at least 4 feet in length, and assorted ¼” quick connect fittings 

 

Sanitizing Cartridge – an empty Waterlogic Filter with cartridge removed 

 

Food Coloring 

 

1.

 

Bypass filters before starting the Descaling Procedure. 
 

2.

 

Put descaler per directions and 3 drops of food coloring into the descaling cartridge. 
 

3.

 

Connect descaling cartridge to the inlet water supply and connect to inlet bulkhead fitting 
on the back of the unit.  Turn on Water Supply. 
 

4.

 

Select Hot Water and depress the Main Dispensing Button on the Front Control Panel until 
descaling solution (colored water) comes out of the faucet.  Container and drain basic will 
be required to catch water from the faucet. 

Содержание WL250













Отзывы: