background image

6

Timer Operation

Meter Immediate Control

A meter immediate control measures water usage and 
regenerates the system as soon as the calculated system 
capacity is depleted. The control calculates the system 
capacity by dividing the unit capacity (typically expressed 
in grains/unit volume) by the feed water hardness and 
subtracting the reserve. Meter Immediate systems 
generally do not use a reserve volume. However, in twin 
tank systems with soft-water regeneration, the reserve 
capacity should be set to the volume of water used during 
regeneration to prevent hard water break-through. A Meter 
Immediate control will also start a regeneration cycle at the 
programmed regeneration time if a number of days equal 
to the regeneration day override pass before water usage 
depletes the calculated system capacity.

Meter Delayed Control

A Meter Delayed Control measures water usage and 
regenerates the system at the programmed regeneration 
time after the calculated system capacity is depleted. As 
with Meter Immediate systems, the control calculates the 
system capacity by dividing the unit capacity by the feed 
water hardness and subtracting the reserve. The reserve 
should be set to insure that the system delivers treated water 
between the time the system capacity is depleted and the 
actual regeneration time. A Meter Delayed control will also 
start a regeneration cycle at the programmed regeneration 
time if a number of days equal to the regeneration day 
override pass before water usage depletes the calculated 
system capacity.

Time Clock Delayed Control

A Time Clock Delayed Control regenerates the system on a 
timed interval. The control will initiate a regeneration cycle 
at the programmed regeneration time when the number 
of days since the last regeneration equals the regeneration 
day override value.

Day of the Week Control

This control regenerates the system on a weekly schedule. 
The schedule is defined in Master Programming by setting 
each day to either “off” or “on.” The control will initiates a 
regeneration cycle on days that have been set to “on” at 
the specified regeneration time.

Control Operation During Regeneration

During regeneration, the control displays a special 
regeneration display. In this display, the control shows the 
current regeneration step number the valve is advancing 
to, or has reached, and the time remaining in that step. The 
step number that displays flashes until the valve completes 
driving to this regeneration step position. Once all 
regeneration steps are complete the valve returns to service 
and resumes normal operation.
Pressing the Extra Cycle button during a regeneration cycle 
immediately advances the valve to the next cycle step 
position and resumes normal step timing.

Control Operation During Programming

The control only enters the Program Mode with the valve in 
service. While in the Program Mode, the control continues 

to operate normally monitoring water usage and keeping 
all displays up to date. Control programming is stored in 
memory permanently, eliminating the need for battery 
backup power.

Manually Initiating a Regeneration

1.   When timer is in service, press the Extra Cycle button for 5 

seconds on the main screen.

2.    The timer advances to Regeneration Cycle Step #1 (brine 

draw & slow rinse), and begins programmed time count 
down.

3.   Press the Extra Cycle button once to advance valve to 

Regeneration Cycle Step #2 (backwash).

4.   Press the Extra Cycle button once to advance valve to 

Regeneration Cycle Step #3 (rapid rinse).

5.   Press the Extra Cycle button once to advance valve to 

Regeneration Cycle Step #4 (brine refill).

6.   Press the Extra Cycle button once more to advance the 

valve back to in service.

NOTE:

 If the unit is a filter, the cycle step order may change.

 NOTE:

 A queued regeneration can be initiated by pressing the Extra Cycle 

button. To clear a queued regeneration, press the Extra Cycle button 
again to cancel. If regeneration occurs for any reason prior to the delayed 
regeneration time, the manual regeneration request shall be cleared.

Control Operation During a Power Failure

The SXT includes integral power backup. In the event of 
power failure, the control shifts into a power-saving mode. 
The control stops monitoring water usage, and the display 
and motor shut down, but it continues to keep track of the 
time and day for a minimum of 48 hours.
The system configuration settings are stored in a non-volatile 
memory and are stored indefinitely with or without line 
power. The Time of Day flashes when there has been a 
power failure. Press any button to stop the Time of Day from 
flashing.
If power fails while the unit is in regeneration, the control will 
save the current valve position before it shuts down. When 
power is restored, the control will resume the regeneration 
cycle from the point where power failed. Note that if power 
fails during a regeneration cycle, the valve will remain in 
it’s current position until power is restored. The valve system 
should include all required safety components to prevent 
overflows resulting from a power failure during regeneration.
The control will not start a new regeneration cycle without 
line power. If the valve misses a scheduled regeneration due 
to a power failure, it will queue a regeneration. Once power 
is restored, the control will initiate a regeneration cycle the 
next time that the Time of Day equals the programmed 
regeneration time. Typically, this means that the valve will 
regenerate one day after it was originally scheduled. If the 
treated water output is important and power interruptions 
are expected, the system should be setup with a sufficient 
reserve capacity to compensate for regeneration delays.

Valve Positions

The position label affixed to the brine cam indicates the 
cycles and service positions of the control valve.

Содержание 6200 SXT





































Отзывы: