background image

Installation and Service Manual – Under-the-Counter Point of Use 5 Stage Reverse Osmosis System 

 

Copyright © 2019 WaterAnywhere  

All Rights Reserved.

 

Page 8 

 

 

Step 2 - Faucet Installation 

For this step, you will need: 

  Faucet assembly kit included with System 

  Tubing, cut to the appropriate length 

 Wrench 

 

 

Install the faucet onto the 
countertop/sink: 

  Find and identify all of the parts in the faucet bag, as 

shown in the diagram. 

  Add the metal washer (2), and then the rubber seal 

(3) onto the threaded nozzle of the faucet (1). 

  Place the faucet nozzle through the previously drilled 

hole in the countertop or sink top, and let it rest on the 
sink top. 

  From the underside of the sink, slide the washers 

onto the threaded stem as shown in the diagram. 

-  (4) & (5) - made of rubber 
-  (6) - made of metal 

 

  Secure the assembly by threading on the locking nut 

(7). 

  Check the orientation and alignment of the faucet and 

washers, adjust as necessary, then use a wrench to 
tighten the locking nut securely 

 Notice:

 

Do not overtighten fittings. 

Install the Tubing 

  Slide the metal nut (10) over the end of the tubing 

with the threads facing up. 

  Add the plastic clamp (9). 

  Press the plastic insert (8) into the end of the tubing. 

  Slide the tubing (until it 

stops) inside the faucet 
nozzle and screw it in by 
hand with the nut that 
was placed on the tubing 
earlier (10). 

  Connect the other end of 

the tubing to the elbow in 
the “out” end of the post 
filter.  

 

Содержание AAA-RO200W





















Отзывы: