background image

10

1.800.556.0595

 

for assistance 

Preparation

The electrician should review the electrical page 
of your WCS Design Drawings and note necessary 
materials, locations, voltage and amperage of all 
electrical components.

 

Tubing and Labeling

Adhere the provided labels to each supply and  
return loop beneath the manifold. Appropriate use  
of these labels will assist in any diagnostic issues. 
These color-coded labels coincide with the color 
labels on the side of the Manifold Controller (MC)  
and those displayed in your WCS Design Drawings.

 

Controls

Warmboard Controls consist of the following: 

 

f

120 VAC thermostats (one per heating zone)   

 

f

120 VAC Manifold Controller (one per manifold)

 

f

24 volt solenoid valve actuators (one per loop)

 

f

Smart Reset Controller (inside Warmsource-E) 

Installing the MC

 

f

Use the provided screws to mount each Manifold 
Controller (MC) inside the manifold cabinet specified 
in the WCS Design Drawings

 

f

Plug the MC into the nearby 120 VAC outlet

 

Installing the Actuators

 

f

Attach actuators to each port on the return manifold

 

f

Connect each actuator wire to the appropriate port 
on the side of the MC, which is pre-labeled and color 
coded. Refer to the WCS Design Drawings as needed

MANIFOLD CABINET

Before installing the controls, you 

MUST

 disable 

Construction Mode by removing the jumper on 
the SRC.

Set the temperature gauge on the front of 
Warmsource-E to 138˚F, though you may set this 
lower if desired.

Содержание Comfort System















Отзывы: