W&T Electronics 58210 Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 63

W&T Electronics 58210 Скачать руководство пользователя страница 54

54

W&T

Firmware-Update

5.4 Updating the TCP/IP-Stack

Prerequisite  is  a  PC  running  under  Windows  9x/NT/2000
with  a  network  connection  and  an  installed  TCP/IP  stack.
You  need  two  files  for  the  update  process:

1. The Update-Tool (32-bit application for Windows9x/

NT/2000), used to perform the update, and

2. the file with the extension

*.bin

(e.g.

C4r1_0.bin

),

which contains the new operating software for the
LAN-Modem. This file is sent to the LAN-Modem.

The  update  process  is  described  in  steps  below.  Please
follow  these  instructions  exactly.  After  an  incomplete
update  the  device  will  no  longer  be  operable!

1. Close all connections that may still be active on the

LAN-Modem. Before the update process all buffers and
their contents are deleted!

2. Start the remote configuration tool of the LAN-Modem

via Telnet

telnet [IP address] 1111

Select the following in the SETUP menu

: System

r

Flash

Update

r

Net Update

and confirm with

y

. The LAN-Modem

closes the Telnet connection, and the green status LED
indicates that it is now in update mode.

3. N o w s t a r t t h e u p d a t e t o o l . T h e m e n u p a t h

C S

programming

r

Flash

takes you to the input screen for

uploading the new firmware.

4. Enter the IP address for the LAN-Modem as well s the

name of the firmware file in the corresponding fields.

«
...
52
53
54
55
56
...
»

Содержание 58210
































































Отзывы:

Нет отзывов