W&T Electronics 58210 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 63

W&T Electronics 58210 Скачать руководство пользователя страница 50

50

W&T

Firmware-Update

5.1 Where do I get the latest firmware?

The current firmware including the update tool and a
revision list is published on our Web site at the following
address:

http://www.wut.de

.

Before  proceeding  with  the  update,  please  write  down
the  5-digit  model  number  located  on  the  LAN-Modem.
F r o m   o u r   h o m e p a g e   y o u   c a n   n o w   f i n d   t h e   p r o d u c t
overview  sorted  by  article  numbers,  from  which  you
arrive  directly  at  the  Web  data  sheet  for  the  respective
LAN-Modem  model.  Then  follow  the  link  to  the  current
version  of  the  firmware.

1

Never interrupt the update process by pulling the

power plug or pressing the reset key. The Com-Ser-
ver will be made inoperable following an incomplete
update.

Never mix files having different version numbers in the
file name. This will make the device inoperable.

T r a n s m i t   a l l   t h e   f i l e s   i n   o r d e r .   T h e   C o m - S e r v e r
automatically  detects  when  all  the  files  have  been  sent
and  the  new  operating  software  is  complete.  It  will  then
automatically  perform  a  reset.

«
...
48
49
50
51
52
...
»

Содержание 58210
































































Отзывы:

Нет отзывов