W&T Electronics 58210 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 63

W&T Electronics 58210 Скачать руководство пользователя страница 41

41

W&T

Modem Operation

Subject to error and alteration

4.4.13 &D (AT&C[0|1|2|3])

= Modem response to DTR option

Default setting: 2

Defines the effect of a level change on the DTR input on the
LAN-Modem. One of four functions may be selected:

•

&D0

The LAN-Modem ignores the signal.

•

&D1

If the LAN-Modem is in data mode,k an ON

r

OFF change

places the modem in command mode. The ATO command
can be used to return to data mode.

•

&D2

A change from ON

r

OFF breaks the existing connection.

A new connection can only be established when an enable
level is present on DTR.

•

&D3

Has  the  same  function  as  &D2  but  additionally  it  resets
the  LAN-Modem.  If  the  LAN-Modem  is  on  data  mode,  a
level  change  on  the  DTR  input  is  only  recognized  if  it  is
present for the time defined in S-register

25

.

4.4.14 &Fn (AT&F[0|1])

= Restore

The LAN-Modem has two factory settings which can be
invoked using the commands

AT&F

and

AT&F1

. The

defaults  specified  by  the  individual  commands  refers
basically  to  the  factory  profile  0.  Factory  profile  1  differs
here  in  the  function  of  the  DTR  input  (

&D0

instead of

&D2

)

and in the flow control (

&K0

instead of

&K3

).

«
...
39
40
41
42
43
...
»

Содержание 58210
































































Отзывы:

Нет отзывов