![background image](http://html2.mh-extra.com/html/wallas/26cc/26cc_installation-manual_3236326043.webp)
Installation
Flue gas connections
Exhaust head
4004
Covering plate 360x360
Fastening screw 4,5x15
1 pcs
2 pcs
8 pcs
Fastening screw 4,5x25
4 pcs
Accessory package contents
2 pcs
1 pcs
Instructions for wall lead-through installation
Accessories
4004
and
4880
are required for the installation.
Note that different measurements for insulation are given for Finland, as opposed
to Sweden and Norway, due to different national regulations.
10. Drill or cut an opening in the wall for
•
the exhaust pipe and its insulation (ø 120 mm, Finland – ø 320 mm, Sweden
and Norway). Note the different measurements for models
26CC
and
40CC
.
•
the combustion air intake pipe (ø 50 mm). The cover plate (16) can be used
as a stencil.
11. Cut both pipes (18 and 21), so that the pipes extend from the wall ca. 40 - 45
mm (23 and 24) when the pipes have been pushed all the way in the heater
connection pipes (25 and 26) and the heater is positioned at least 70 mm (Fin-
land) / 100 mm (Sweden and Norway) from the wall.
12. Install the cover plates (16 ja 17) on the lead-through openings and seal the
connection between the wall and the plate with silicone paste.
13. Push the pipes (18 and 21) all the way into the connection pipes (25 and 26)
and seal the exhaust pipe’s connection (25) with a pipe clamp (11) and the
combustion air pipe’s connection (26) with a hose binder (10). (Both ties can be
found in the heater accessory bag.) The exhaust pipe cannot be tightened suf-
ficiently by any other fastening than a pipe clamp (11), which must be tightened
sufficiently to lock the pipe in place.
14. Place mineral wool (19) on the exhaust pipe (18) so that the insulating material
extends from the back surface of the heater to ca. 10 mm outside the wall (27).
Place the insulation mantel plate (20) on the insulation.
15. Then, push the heater to a distance of 70 / 100 mm from the wall, while guiding
the hoses and the insulation through the lead-through openings.
16. Adjust the length of the insulation mantel plate (20), by cutting it so that its end
Exhaust head
4004
Mounting kit
4880
en
Exhaust head 4004
Insulating channel
4012
Insulation mantel plate, 0,3 m
4015
Exhaust pipe
4845
Combustion air pipe
4045
Mounting kit 4880
Comb. air intake shield
4051
26CC / 40CC
D80151
- 43 -
15
16
15
17
17
16
19
20
18
21
22
0,5 m
0,5 m
19
21
18
1 m
20
22
30
34
(Directive 2002/95/EY) requirements.
(Directive 2002/95/EY) requirements.
490525C
Содержание 26CC
Страница 12: ...12 D80150 Tekniset tiedot Toimintaperiaate fi 26CC 40CC P 12 V 490525C...
Страница 40: ...Technical information Operating principles en 26CC 40CC D80151 40 P 12 V 490525C...
Страница 68: ...Teknisk information Driftsprinciper sv 26CC 40CC D80152 68 P 12 V 490525C...
Страница 96: ...Teknisk informasjon Driftsprinsipper no 26CC 40CC D80158 96 P 12 V 490525C...