WAGO 765-1205/0100-0000 страница 81 Скачать руководство пользователя

Страница: 81 / 102

765-1205/0100-0000

Diagnostics

Product manual | Version: 1.0.0

8DIO FLD EC DC 24V 2.0A

LED

Color

State

Description

Green

Link:

The module has a connection to the

ETHERNET, but is not sending/receiving
Ethernet frames.

Green

Flickering (load-de-
pendent)

Activity:

The module has a connection to

ETHERNET and is sending/receiving Ether-
net frames.

Off

The module is not connected to the ETH-
ERNET.

–

LED yellow

Off

This LED is not used.

Table 61: LED States ETHERNET Status

LED State

Definition

Flickering
(load-dependent)

The indicator switches on and off at a frequency of 10 Hz, indicating high ETHERNET
activity:
on for 50 ms and then off for 50 ms.
The indicator switches on and off at irregular intervals to indicate low ETHERNET activ-
ity.

Bluetooth

Status

The Bluetooth

LED is integrated into the Bluetooth

antenna and indicates the connec-

tion status.

Table 62: LED States

LED

Color

State

Description

Duo LED, blue/red

Blue

Bluetooth

connection established

Off

Bluetooth

inactive

Port Status

LEDs 0 (port X01), 1 (port X02), ..., 7 (port X08) indicate the status of the digital input/out-
put module.

Table 63: Port Status

LED

Color

State

Description

0, 1, 2, ...

Port Status

(pin 4)

Duo LED, yellow/red (yellow = simultaneously red and green)

yellow

Status of digital input/output: 1

Off

Status of digital input/output: 0

red

Overload, short circuit (pin 4 and pin 3)

red

Flashing 1 Hz

Overload, sensor supply short circuit (pin 1
and pin 3)

11.2 Diagnostics via EtherCAT

11.2.1 Diagnostic History

Table 64: Diagnostic History (Index 0x10F3)

Subindex Name

Explanation

Type

Flags

Default

Highest supported
subindex

Highest supported subindex

UINT8

Содержание 765-1205/0100-0000







































































































Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды

WAGO 765-1205/0100-0000, Руководство пользователя

Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды