WAGO 765-1205/0100-0000 Скачать руководство пользователя

Страница: 76 / 102

765-1205/0100-0000

Commissioning

Product manual | Version: 1.0.0
8DIO FLD EC DC 24V 2.0A

The following table lists port-specific configuration parameters.

Table 48: Port-Specific Configuration Parameters

Node Name

Node Class

Access Default Description

OverCurrentPin1, Over-
CurrentPin2, OverCur-
rentPin4

Variable

Read

Warning level for current upper limit on pin 1, pin
2 or pin 4; unit: 1 mA

0: monitoring not enabled

UnderCurrentPin1, Un-
derCurrentPin2, Under-
CurrentPin4

Variable

Read

Warning level for current lower limit on pin 1, pin
2 or pin 4; unit: 1 mA

0: monitoring not enabled

10.3.3.1.3 Read Process Data

The OPC UA server provides nodes with process data. For example, the OPC UA client
can read out the value on pin 2 of a port in the

Pin2ProcessData

node. The path to this

node is:

Root > Object > DeviceSet > [device name] > DigitalConnector >

PortXX > ProcessData

Note

OPC UA client can only read process output data

The process output data is written by the EtherCAT controller. The OPC UA client can
only read process output data.

The following table lists port-specific process data.

Table 49: Port-Specific Process Data

Node Name

Node Class

Access

Description

Pin2ProcessData

Variable

Read

Process data on pin 2

Pin4ProcessData

Variable

Read

Process data on pin 4

10.3.3.1.4 Read Measured Values

The OPC UA server provides nodes with calculated measured values. For example, the
OPC UA client can read out the calculated total current of supply cable 1 in the

SumCur-

rentL

node. The path to this node is:

Root > Object > DeviceSet > [device name] > DigitalConnector > Di-

agnostics > Current

The following table lists device-specific (calculated) measured values.

Table 50: Device-Specific (Calculated) Measured Values

Node Name

Node Class

Access

Description

SumCurrentL

Variable

Read

Total current in supply cable 1 calculated
from individual measurements; unit: mA

SumCurrentL2

Variable

Read

Total current in supply cable 2 calculated
from individual measurements; unit: mA

MeanTemperature

Variable

Read

Average value for the temperature of the
assembly, calculated from the temperature
values measured individually on the three
chips; unit: °C

Содержание 765-1205/0100-0000







































































































Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды

WAGO 765-1205/0100-0000, Руководство пользователя

Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды