WAGO 765-1205/0100-0000 страница 69 Скачать руководство пользователя

Страница: 69 / 102

765-1205/0100-0000

Commissioning

Product manual | Version: 1.0.0

8DIO FLD EC DC 24V 2.0A

Performing a Reset

Proceed as follows to reset the Bluetooth

firmware:

•

Click

Reset

The Bluetooth

firmware is reverted and restarts.

Switching the Bluetooth

Interface Wireless Transmitter on/off

To switch the Bluetooth

interface wireless transmitter on:

•

Slide the

Bluetooth radio

switch to the right

The Bluetooth

interface wireless transmitter switches on.

To switch the Bluetooth

interface wireless transmitter off, slide the

Bluetooth radio

switch to the left.

Switching LED Forcing on/off

Proceed as follows to switch LED forcing (externally controlled LED mode) on:

•

Slide the

LED forcing

switch to the right.

LED forcing switches on. The LED on the Bluetooth

interface can now be externally

controlled.

To switch LED forcing off, slide the

LED forcing

switch to the left.

10.3.1.4.7 Logging Users on and off and Managing Them

Logging Users on

Proceed as follows to log users on:

1. From the Webserver main menu (left), select the

Sign in

menu item.

The input screen for username and password appears:

Figure 20:

Sign in

Menu Item – Input Screen for Username and Password

Содержание 765-1205/0100-0000







































































































Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды

WAGO 765-1205/0100-0000, Руководство пользователя

Результаты поиска

Содержание 765-1205/0100-0000

Отзывы:

Похожие инструкции для 765-1205/0100-0000

Бренды по названию

Популярные бренды