WAGO 765-1205/0100-0000 Скачать руководство пользователя | Manualshive

Страница: 37 / 102

background image

765-1205/0100-0000

Planning

Product manual | Version: 1.0.0

37

8DIO FLD EC DC 24V 2.0A

6.2.2 Requirements on the Power Supply

Power Source

Note

PELV or SELV power source required

Only device the product with 24 VDC PELV (Protective Extra Low Voltage) or SELV
(Safety Extra Low Voltage) voltage sources. Failure to do so may result in electric shock.

If L1 and L2 are to be supplied separately (e.g., for safe switch-off of L2), then either cen-
tral grounding must be implemented using two power supply units, or the power supply
connection must be made on the same phase. However, the use of two separate power
supply units is not mandatory.

Note

Note the following when L1 and L2 are supplied separately:

If L1 and L2 are to be supplied separately (e.g., for safe switch-off of L2), then either cen-
tral grounding must be implemented using two power supply units, or the power supply
connection must be made on the same phase. Use of two separate power supply units is
not mandatory.

Fuse Protection

Always protect the power supply lines from the power supply unit to the first module with
a device circuit breaker or fuse. For this purpose, use a 24 VDC / max. 16 A fuse or cir-
cuit breaker with type B trip characteristics.

Note

Device damage if maximum supply current exceeded

The maximum supply current must not be exceeded. Otherwise, there is a risk of damage
to the PCB of the device and the pluggable connector.

6.2.3 Additional Measures

The setup must ensure that the total current the flows back through pin 3 does not ex-
ceed the load limit.

The values of all currents on all pins of all connections (except for pin 3 = ground pin) and
the calculated total currents of the two supply cables are measured by the chip used in
the 765 Series products and thus can be recorded by a monitoring application. These val-
ues can be accessed via the OPC UA server, for example.

On the basis of these measured values, a monitoring application with integrated current
management can be implemented. This can regularly verify that all monitoring functions
are satisfied on the basis of the measured current values and also monitor the tempera-
tures and voltages on the connections.

«
...
35
36
37
38
39
...
»

Содержание 765-1205/0100-0000







































































































Отзывы:

Нет отзывов

Похожие инструкции для 765-1205/0100-0000

Бренд: Spon Страницы: 9

Бренд: Aiwa Страницы: 20

Бренд: Viking Страницы: 4

Бренд: iTrak Страницы: 6

HBW8AQ 1M Series

Бренд: Halsey Taylor Страницы: 4

HomeMatic HMW-IO-12-FM

Бренд: eQ-3 Страницы: 36

Бренд: JBL Страницы: 2

Бренд: human care Страницы: 24

Бренд: MAHLE Страницы: 20

Бренд: M-E Страницы: 36

Бренд: Koch Страницы: 4

Бренд: Commax Страницы: 28

Бренд: Emos Страницы: 52

Бренд: Xiron Страницы: 29

Wireless music system for iPod

Бренд: Brookstone Страницы: 14

Бренд: InfinitePlay Страницы: 27

Jacketed Unitank

Бренд: Ss Brewtech Страницы: 14

MaxPure MPDI DI System

Бренд: SpectraPure Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды