Wacker Neuson E09-01 Скачать руководство пользователя страница 78

Страница: 78 / 188

3-36

BA 1404 en – Edition 2.7 * * 1404b330.fm

Operation

3.19 Retracting belt (option)

Danger

Injury hazard! Do not drive or work with the seat belt unbuckled.

Causes serious injury or death.

☞

Fasten and adjust your seat belt before moving off or operating the machine.

☞

Do not twist the seat belt when you fasten it.

☞

Firmly fasten your seat belt over your hips and not over your stomach.

☞

Do not place the seat belt over hard, edged or fragile items (for example tools).

☞

Seat belt buckle must not be obstructed by foreign bodies (paper or simi-
lar); otherwise the buckle latch cannot lock into place.

☞

The seat belt must be replaced by an authorized workshop after an acci-
dent, and the bearing capacity of the fastening points and seat fixtures must
be checked.

☞

Check the seat belts at regular intervals. Have damaged parts immediately
replaced by an authorized workshop.

Seat belt

is for the operator’s safety.

Fastening the seat belt:

☞

Fasten the seat belt as follows before starting the machine:

• Hold belt on buckle latch

and run it slowly and steadily over the hips to buckle

• Insert buckle latch

into buckle

with an audible click

(pull test)

• Tighten the seat belt by pulling at its end

➥

The seat belt must be tightly in place over the hips!

Abb. 91: Unwinding the seat belt

Abb. 92: Fastening the seat belt

Содержание E09-01





























































































































































































Результаты поиска

Содержание E09-01

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E09-01, Руководство оператора

Результаты поиска

Содержание E09-01

Отзывы:

Бренды по названию

Популярные бренды