Wacker Neuson E09-01 Скачать руководство пользователя страница 107

Страница: 107 / 188

BA 1404 en – Edition 2.7 * 1404b340.fm

3-65

Operation

Right-hand control lever

Emergency lowering

Danger

Crushing hazard during boom lowering!

Causes serious crushing or injury resulting in death.

☞

Ensure that no one is in the danger zone.

Observe the following during emergency lowering:
1

Turn the starting key to position 1.

Lower both control lever bases.

Push the right-hand control lever

forward until the boom is fully lowered to the

ground.

Return the control lever to neutral.

Abb. 134: Control lever on the right

Position

Lever

Function

• E

☞

Forward

➥

Boom is lowered

• F

☞

To the right

➥

Tilt out the bucket

• G

☞

Backward

➥

Boom is raised

• H

☞

To the left

➥

Tilt in the bucket

Button

Function

☞

➥

Horn

Abb. 135: Emergency lowering

Содержание E09-01





























































































































































































Результаты поиска

Содержание E09-01

Отзывы:

Бренды по названию

Популярные бренды

Wacker Neuson E09-01, Руководство оператора

Результаты поиска

Содержание E09-01

Отзывы:

Бренды по названию

Популярные бренды