Wacker Neuson E09-01 Скачать руководство пользователя страница 138

Страница: 138 / 188

5-10

BA 1404 en – Edition 2.7 * * 1404b510.fm

Maintenance

Checking the coolant level

•

Park the machine on level ground

•

Stop the engine!

•

Raise the control lever base

•

Remove the starting key and carry it with you

•

Let the engine and the coolant cool down

•

Open the engine cover

•

Check the coolant level on the transparent coolant reservoir

and on the radiator

☞

If the coolant level is below the

LOW

seam or if there is no coolant at the radiator’s

filler inlet:

➥

Adding coolant

Notice!

Check the coolant level once a day.
We recommend checking it before starting the engine.

Adding coolant

After the engine has cooled down:

☞

Release overpressure in the radiator

☞

Carefully open cap

to the first notch and fully release the pressure

☞

Open filler cap

☞

Add coolant up to the lower edge of the filler inlet (radiator)

☞

Close filler cap

☞

Start the engine and let it warm up for about 5 – 10 minutes.

☞

Stop the engine

☞

Remove the starting key and carry it with you

☞

Let the engine cool down

☞

Check the coolant level again

➥

The coolant level must be between the

LOW

and

FULL

reservoir seams

☞

If necessary, add coolant and repeat the procedure until the coolant level remains constant

☞

Close and lock the engine cover

Caution!

Do not mix the coolant with other coolants.

☞

Use only the coolant prescribed by Wacker Neuson

– see chapter 5.17

Flu-

ids and lubricants

on page 5-35.

Notice!

Check the antifreeze every year before the cold season sets in

Abb. 186: Radiator

Coolant reservoir

FULL

LOW

Содержание E09-01





























































































































































































Результаты поиска

Содержание E09-01

Отзывы:

Wacker Neuson E09-01, Руководство оператора, Страница: 138 / 188

Результаты поиска

Содержание E09-01

Отзывы: