Wacker Neuson DT10 Скачать руководство пользователя | Manualshive

Страница: 28 / 120

background image

2-8

BA DT10 en - Edition 1.5 * * dt10b210.fm

Safety instructions

• Have loads fastened and crane operators guided by experienced persons only!

The person guiding the crane operator must be within sight or sound of him.

• Always use specially designed or otherwise safety-oriented ladders and working

platforms to perform overhead assembly work.
Never use machine parts or attachments/superstructures as a climbing aid!
Wear a safety harness when performing maintenance at greater heights!
Keep all handholds, steps, handrails, platforms, landings and ladders free from dirt,
snow and ice!

• Clean the machine, especially connections and threaded unions, of any traces of oil,

fuel or preservatives before performing maintenance/repair work!
Do not use aggressive detergents!
Use lint-free cleaning rags!

• Before cleaning the machine with water, steam jet (high-pressure cleaner) or deter-

gents, cover or tape up all openings which – for safety and functional reasons – must
be protected against water, steam or detergent penetration. Special care must be taken
with the electrical system

• After cleaning, remove all covers and tapes applied for that purpose!
• After cleaning, examine all fuel, lubricant and hydraulic oil lines for leaks, chafe marks

and damage!
Rectify all malfunctions without delay!

• Always tighten any threaded fittings that have been loosened during maintenance and

repair!

• Any safety devices removed for set-up, maintenance or repair purposes must be

refitted and checked immediately upon completion of the maintenance and repair work

• Ensure that all consumables and replaced parts are disposed of safely and with

minimum environmental impact!

• Do not use the work equipment as lifting platforms for persons!
• Before taking up work on machine parts dangerous for life and limb (bruising, cutting),

always ensure safe blocking/support of these areas.

• Perform maintenance and repair work beneath a raised machine, attachments or

additional equipment only if a safe and secure support has been provided for (the sole
use of hydraulic cylinders, jacks, etc. does not sufficiently secure raised machines or
equipment/attachments).

• During operation and for a certain time after using the machine, do not touch hot parts

such as the engine block and the exhaust system - risk of burns!

• Retainer pins can fly out or splinter when struck with force – injury hazard!
• Do not use starting aids (for example start pilot)! This especially applies to those cases

in which a heater plug (intake-air preheating) is used at the same time – explosion
hazard!

• Apply special care when working on the fuel system – increased fire hazard!

«
...
26
27
28
29
30
...
»

Содержание DT10

























































































































Отзывы:

Нет отзывов

Похожие инструкции для DT10

Бренд: ABB Страницы: 50

ACS880-01 Series

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 36

Бренд: ICS Schneider Messtechnik Страницы: 124

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: Rane Страницы: 6

Бренд: Rane Страницы: 27

Бренд: Ranger Products Страницы: 6

Бренд: Rane Страницы: 88

Бренд: Haag-Streit Страницы: 21

LED PowerBank 48

Бренд: SHOWTEC Страницы: 12

Бренд: ACS Страницы: 28

Бренд: ICS Страницы: 156

PulseDose LT PD1000

Бренд: DeVilbiss Страницы: 58

Бренд: Cuisinart Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды