manualshive.com logo in svg

Wacker Neuson BFS 1345, Руководство оператора

Поделиться
Скачать
Wacker Neuson BFS 1345 Скачать руководство пользователя страница 5

5

Foreword

1.

Foreword

For your own safety and protection from bodily injuries, carefully read,
understand and follow the safety information in this manual.

Please operate and maintain your Wacker Neuson machine in accor-
dance with the instructions in this operator's manual. Your Wacker
Neuson machine will reward you with troublefree operation and a high
degree of availability.

Defective components must be replaced immediately.

All rights, especially the right for copying and distribution, are reserved

Copyright 2008 by Wacker Construction Equipment AG

No part of this publication may be reproduced in any form or by any
means, electronic or mechanical, including photocopying, without ex-
press permission in writing from Wacker Construction Equipment AG.

Any type of reproduction, distribution or saving on data carriers of any
type or method not authorized by Wacker Neuson represents an infringe-
ment of valid copyrights and will be prosecuted. We expressly reserve
the right to make technical modifications - even without special notice -
which aim at further improving our machines or their safety standards.

Содержание BFS 1345











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды