manualshive.com logo in svg

Wacker Neuson BFS 1345, Руководство оператора

Поделиться
Скачать
Wacker Neuson BFS 1345 Скачать руководство пользователя страница 22

Operation

T01110en.fm

22

6.7

Assembling the cutting blade

6.7.1

Checking a new cutting blade:

∗

The blade type must be suitable for the material to be cut. Observe the
peripheral speed, refer to the "Technical data"!

∗

The arbor diameter of the cutting blade must precisely fit the shaft to
ensure smooth blade running.

∗

The cutting blade must be undamaged.
Observe the correct direction of rotation of the cutting blade! That
means the rotational direction mark on the cutting blade must
correspond with the rotational direction mark on the cutting blade
guard.

6.7.2

Proceed as follows for the assembly of the cutting blade:

1. Fold up the cutting blade guard (1).

2. Prior to the assembly of the cutting blade, clean the spring washers

and the locking pin and check them for damage.

3. Attach cutting blade and spring washer on the shaft. 

4. Tighten the hexagonal bolt firmly. To do this, apply counter pressure

on the spanner surfaces of the cutting shaft.

5. Fold down the cutting blade guard.

Starting the machine is only permitted with a water hose connected
and the water supply turned on.
 

Содержание BFS 1345











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды