manualshive.com logo in svg

Wacker Neuson BFS 1345, Руководство оператора

Поделиться
Скачать
Wacker Neuson BFS 1345 Скачать руководство пользователя страница 26

Operation

T01110en.fm

26

4.

Close the choke.

∗

If the engine is warm or at high ambient temperatures, open the choke
approximately half way or fully.

∗

If the engine is cold or at low ambient temperatures, close the choke.

5.

Recoil starter

∗

Slowly pull the recoil starter handle until you can feel resistance
(compression stroke). Return the recoil starter handle to its original
position and pull with force. Do not pull out the entire length of the rope.

∗

As soon as the engine has started, rewind the starter rope by slowly
returning the recoil starter handle to its original position.

6.

Choke

∗

After the engine has been started, slowly open the choke and then
leave it in the fully open position.

∗

If the engine is cold or at low ambient temperatures, never fully open
the choke immediately after the engine has been started or the engine
will stall.

Pu

ll q

uic

kly

Open

Содержание BFS 1345











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды