manualshive.com logo in svg

Wacker Neuson BFS 1345, Руководство оператора

Поделиться
Скачать
Wacker Neuson BFS 1345 Скачать руководство пользователя страница 15

Description

T01067en.fm

15

4.4

General instructions for use for diamond-edged cutting blades

∗

Never use a cutting blade with a larger diameter than necessary in or-
der to cut a certain depth.

∗

If the cutting blade comes to a standstill, remove it from the cut before
starting the machine again. If the cutting blade comes to a standstill in
the cut, check whether the belt is tightened adequately. Check the ten-
sion screw and make sure that it is tightened properly.

∗

Cut in a straight line. Mark the cutting line clearly in such a way that the
operational personnel can follow it easily. This is to ensure that the
floor saw machine does not need to be redirected from one side to the
other (avoid cutting tight curves).

∗

Sufficient drive power is essential! When cutting, work at full throttle.

∗

Caution on steep tracks and levels! The machine must not exert lateral
force against the blade.

∗

Never exceed the maximum speeds (imprinted on cutting blade)!

∗

Use a suitable diamond-edged cutting blade for the material to be cut
(asphalt, concrete ...). Wacker Neuson offers an extensive range of di-
amond-edged cutting blades in different qualities.

∗

Do not cut into the gravel area using diamond-edged cutting blades.
When cutting on the edge of the track or when cutting two different ma-
terials (cutting in the joint area), uneven wear is possible. Check care-
fully for irregularities (reinforcements etc.) in the material to be
processed. These can overload the cutting blade very quickly. When
starting cutting operations, work carefully and with a low down speed.

∗

Do not process loose materials (e. g. paving stones).

 

Содержание BFS 1345











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды