manualshive.com logo in svg

Wacker Neuson BFS 1345, Руководство оператора

Поделиться
Скачать
Wacker Neuson BFS 1345 Скачать руководство пользователя страница 31

Maintenance

T01071en.fm

31

7.4

Cleaning the air cleaner

A dirty air cleaner causes starting difficulties, a drop in power, engine
faults and considerably reduces the service life of the engine. Always
keep the air cleaner cartridge clean.
Therefore, the air cleaner cartridge has to be cleaned regularly. During
the installation, the paper element and the polyurethane foam must be
placed on the bottom part. Make sure that the nozzle has been
installed and then tighten the filter cover with the plastic nut.
Cleaning the urethane foam:
Clean the filter element in a detergent solution and then allow it to
completely dry.
Clean the urethane foam filter element every 50 hours.
Paper element:
Clean the paper element by knocking it gently. Never use oil.
If the engine is operated in extremely dusty areas, the air cleaner
elements must be cleaned and replaced more often.

 

7.5

Cleaning the screws, nuts and bolts

Retighten loose screws and nuts. Check for fuel and oil leaks. Always
ensure optimum operating safety.

  

Plastic nut

Air cleaner cap

Urethane foam

Element

Содержание BFS 1345











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды