VTI Instruments EMX-75 Series Скачать руководство пользователя

Страница: 6 / 61

VTI Instruments

EMX-75XX Preface

ARNINGS

ONT

Avoid Electric Shock

To avoid electric shock or fire hazard, do not operate this product

with the covers removed. Do not connect or disconnect any cable,

probes, test leads, etc. while they are connected to a voltage source.

Remove all power and unplug unit before performing any service.

Service should only be performed by qualified personnel.

Ground the Product

This product is grounded through the grounding conductor of the

power cord. To avoid electric shock, the grounding conductor must

be connected to earth ground.

Operating Conditions

To avoid injury, electric shock or fire hazard:

Do not operate in wet or damp conditions.

Do not operate in an explosive atmosphere.

Operate or store only in specified temperature range.

Provide proper clearance for product ventilation to prevent

overheating.

DO NOT operate if any damage to this product is suspected.

Product should be inspected or serviced only by qualified

personnel.

Improper Use

The operator of this instrument is advised that if the equipment is

used in a manner not specified in this manual, the protection

provided by the equipment may be impaired.

Conformity is checked by inspection.

Содержание EMX-75 Series






























































Результаты поиска

Содержание EMX-75 Series

Отзывы:

Похожие инструкции для EMX-75 Series

Бренды по названию

Популярные бренды

VTI Instruments EMX-75 Series, Руководство пользователя

Результаты поиска

Содержание EMX-75 Series

Отзывы:

Похожие инструкции для EMX-75 Series

Бренды по названию

Популярные бренды