51
• L'appareil doit être monté de sorte à garantir que, durant des conditions de service normales, personne ne puisse se
trouver à proximité de parties en mouvement ou sous tension.
• En cas de démontage de l'appareil, avec des instruments appropriés ; extraction de l'échangeur de chaleur ; extraction
du module des moteurs ; l'appareil devra être préalablement éteint et débranché du réseau d'alimentation électrique.
• Raccorder l'appareil au réseau d'alimentation/prise électrique seulement si le débit de l'installation/prise est adapté à sa
puissance maximale. Dans le cas contraire, contacter immédiatement un professionnel qualifié.
• Éteindre l'interrupteur général de l'installation quand : on détecte un dysfonctionnement ; on décide de réaliser un
entretien de nettoyage extérieur ; on décide de ne pas utiliser l'appareil pendant un brève ou longue période.
• L'appareil ne peut pas être utilisé comme activateur de chauffe-eau, radiateurs, etc., et ne doit pas extraire de l’air dans
des conduits utilisés pour l’évacuation d’air chaud/de fumées provenant d’un quelconque appareil à combustion.
• L'appareil doit expulser l’air vers l’extérieur à travers un conduit spécifique.
• L’appareil est conçu pour extraire uniquement de l’air pur, (c’est à dire sans éléments graisseux, suies, agents chimiques
ou corrosifs, mélanges explosifs ou inflammables.
• Ne pas couvrir ni obstruer la grille d'aspiration et le refoulement de l'appareil de sorte à garantir le passage optimal de
l'air.
• Température maximale de fonctionnement : 45°C.
•
L'installation de l'appareil est réservée à des techniciens qualifiés.
•
L’installation électrique à laquelle le produit est raccordé doit être conforme aux normes en vigueur.
•
Pour l'installation, prévoir un interrupteur unipolaire ayant une distance d'ouverture des contacts
égale ou supérieure à 3 mm, qui permette la déconnexion complète dans les conditions de catégorie
de surtension III.
•
Les produits équipés de moteurs prédisposés au câblage monophasé (M) nécessitent TOUJOURS
d'une connexion à des lignes monophasées à 220-240 V (ou
seulement 230 V quand le produit le prévoit). Toute sorte de
modification est considérée comme une manipulation du produit et
annule la garantie correspondante.
•
Il n'est pas nécessaire d'effectuer de réglage spécifique étant
donné que les appareils fonctionnent aux fréquences nominales
sans programmation préliminaire.
• Les données électriques du réseau doivent correspondre à celles reportées sur
la plaque A (fig.1).
FRANCAIS
1
A
Содержание VORT HR 450 Avel D
