Volvo Penta D1 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 92

background image

Starting the Engine

Activate the control panel by depressing the on/off
button (1). The Volvo Penta logo is displayed in the
window. Two audible signals are sounded to indicate
the system is ready and that the engine may be started.

Check the tachometer

If an operational fault occurs an audible alarm will
sound and a symbol will flash in the tachometer
window. Refer to the

Fault handling, page 41

for more detailed information and recommended
actions.

Check the alarm instrument (accessory).

The lamps in the alarm instrument light up each time the
ignition is turned on. Check that all lamps light up and
then extinguish. If any lamp flashes, a fault has been
registered; refer to the

Fault handling, page 41

for more detailed information and recommended
actions.

Start the engine

Press the start button (4). Release the start button as
soon as the engine starts.
The pre-heating symbol is displayed in the tachometer
window. Pre-heating is automatic and lasts for 20
seconds.
Pre-heating only takes place if engine temperature is
below 50° (122° F).
Pre-heating may be activated before the engine is
started by depressing the start button (4) for a short
moment. Pre-heating will continue for 20 seconds. The
pre-heating symbol is displayed in the tachometer
window.

!

!

+

-

0

3

2

1

4

RPMX1000

P0008437

Starting

47711262 01-2019 © AB VOLVO PENTA

33

«
...
33
34
35
36
37
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов

Похожие инструкции для D1 Series

Бренд: Sailfish Страницы: 44

Бренд: KAYAKS2FISH Страницы: 17

Spartan 57076-1

Бренд: Traxxas Страницы: 30

Invitation Triss Racer

Бренд: BOMBARDIER Страницы: 23

Cross 46 Side Console

Бренд: YAMARIN Страницы: 51

Бренд: Peinert Страницы: 4

Бренд: Prestige Страницы: 116

Бренд: Everglades Страницы: 126

Бренд: YAMARIN Страницы: 36

Бренд: Ocean Kayak Страницы: 5

Бренд: Lagoon Страницы: 80

Cap Camarat 625 WA

Бренд: Jeanneau Страницы: 68

SUN ODYSSEY 42 DS

Бренд: Jeanneau Страницы: 136

Бренд: Rave Sports Страницы: 16

Turbojet J/T 285

Бренд: Williams Страницы: 23

Бренд: Quicksilver Страницы: 47

Sun Marine Frp-330

Бренд: boAt Страницы: 3

Бренд: J Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды