Volvo Penta D1 Series Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 92

background image

Seawater System

The raw water system is the engine's external cooling
system. On engines with drives, the raw water pump
sucks in water via the drive, through the control
system's oil cooler to the raw water pump. The water
then passes through the raw water filter before being
pumped through the fuel cooler, intercooler, engine oil
cooler and heat exchanger. Finally the water is fed out
through the exhaust elbow, where it is mixed with the
exhaust gases.
On engines with reverse gears, the raw water pump
sucks in water via a raw water intake, after which the
water passes a raw water filter (extra equipment)
before being pumped through the intercooler, heat
exchanger, engine oil cooler and gearbox oil cooler.
Finally the water is fed out through the exhaust elbow,
where it is mixed with the exhaust gases.

WARNING!

Risk of water entry. Water will flow into the boat if any
hose, plug etc. located below the waterline is removed
when the boat is in the water. Always close the sea
cocks. If the boat does not have sea cocks the water
flow must be blocked in a safe manner. If this is not
possible, the boat must be drawn up on land before
work starts.

Maintenance

60

47711262 01-2019 © AB VOLVO PENTA

«
...
60
61
62
63
64
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов

Похожие инструкции для D1 Series

Бренд: PROAQUA Страницы: 24

Бренд: Bestway Страницы: 24

CAP CAMARAT 7.5 CC serie 2

Бренд: Jeanneau Страницы: 112

Mirage Vantage CT

Бренд: Hobie Страницы: 28

Бренд: intrepid Страницы: 52

Бренд: Ranger boats Страницы: 78

Бренд: Grand Soleil Страницы: 103

RISING FLOW SLSUPB636

Бренд: SereneLife Страницы: 8

Бренд: C-Yacht Страницы: 75

Бренд: Alliaura Marine Страницы: 78

Бренд: SEALVER Страницы: 16

Бренд: Pelican Страницы: 2

Бренд: Galaxy Страницы: 24

Бренд: Ocean Kayak Страницы: 5

Бренд: Ranger Tugs Страницы: 36

Бренд: Quicksilver Страницы: 87

Бренд: Jensen Marine Страницы: 22

Бренд: Camper & Nicholson Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды