Volvo Penta D1 Series Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 92

background image

Maintenance

This chapter contains general technical information and instructions on how the prescribed maintenance items
must be carried out. Read through the instructions carefully before starting work. The times when maintenance
items must be carried are indicated in the

Maintenance Schedule, page 46

Read through the safety precautions for maintenance and service in the

Safety precautions for maintenance and

service operations

chapter before work on the engine is begun.

Volvo Penta recommend that all servicing with the engine running should be undertaken by an authorized Volvo
Penta workshop.

WARNING!

Care and maintenance work should be done with the engine stopped unless otherwise specified. Stop the engine
before opening or removing the engine hatch/hood. Make it impossible to start the engine by removing the start
key and cutting the system voltage with the main switches.

NOTICE!

More information on how to perform service and maintenance can be found in the Service and

Maintenance handbook. Information on how to purchase the Service and Maintenance handbook can be found
at www.volvopenta.com.

47711262 01-2019 © AB VOLVO PENTA

47

«
...
47
48
49
50
51
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов

Похожие инструкции для D1 Series

Бренд: Nauticstar Страницы: 82

Bravura 21 Series

Бренд: Supra Страницы: 90

Merry Fisher 645

Бренд: Jeanneau Страницы: 84

Cross 57 Bow Rider

Бренд: YAMARIN Страницы: 51

Бренд: Hydrospace Страницы: 115

Бренд: whaler Страницы: 88

Бренд: BRIG Страницы: 36

Бренд: C-Yacht Страницы: 75

Бренд: Access Dinghies Страницы: 4

Бренд: Defender Страницы: 16

Бренд: Hunter Страницы: 20

Бренд: Polaris Страницы: 114

Бренд: Rondar Страницы: 16

Бренд: BENETEAU Страницы: 238

Бренд: Zboat Страницы: 35

MERRY FISHER 695 MARLIN

Бренд: Jeanneau Страницы: 116

sun odyssey 33I

Бренд: Jeanneau Страницы: 136

Бренд: Columbia Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды