Volvo Penta D1 Series Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 92

Volvo Penta D1 Series Скачать руководство пользователя страница 43

Fault handling

Despite regular maintenance according to the maintenance schedule and perfect operation conditions, faults that
need to be attended to during travel, may occur. This chapter describes some possible alarms and fault handling.
Note that the content of this chapter does not provide full coverage of the possible fault messages and alarms.
Contact a Volvo Penta workshop for assistance with diagnostic readouts and unresolved faults.

0

3

2

1

4

RPMX1000

SYSTEM INFORMATION

1

ON/Off START

ALARM/DIM STOP

2

P0016957

If an operational fault arises an audible alarm will
sound and a symbol will flash in the tachometer
window(

1

) If optional equipment such as an alarm

monitor or an EVC display are installed, the relevant
warning lamp will flash there also.
Cancel the alarm by depressing the multi-function
button (

2

). The audible alarm will be silenced. The

symbol will be lit continuously until the fault is
remedied.
This chapter describes faults and actions to be taken.

CAUTION!

Read the safety precautions for maintenance and
service in the Maintenance Safety Information
chapter before starting work.

47711262 01-2019 © AB VOLVO PENTA

41

«
...
41
42
43
44
45
...
»

Содержание D1 Series





























































































Отзывы:

Нет отзывов