manualshive.com logo in svg

Volter ROXER xRover S, Руководство по эксплуатации

Поделиться
Скачать
Volter ROXER xRover S Скачать руководство пользователя страница 7

 

 

 

7 

MAINTENANCE, CARE AND STORAGE OF STROLLER/BABY BUGGY 

 

A. 

Maintenance of the bike hitch

  

- Before each ride make sure that the hitch and safety strap are connected properly.  
- Regularly check that the hitch is not damaged, broken, etc. Replace it in the case of the first sign of damage.  
- Any damage/break of any part of the xRover stroller/baby buggy should be repaired/replaced immediately to prevent 
any personal injuries. 
B. 

Care for the covering/hood

  

–

 Your xRover stroller is made of a durable, strong, waterproof fabric 

–

 

Kortexin™ or Cordura™. Clean the covering only 

with ordinary soap or a mild cleaner and warm water. Let air dry. 
 

 
 
 
 
 
 
 
 

 
C. 

Wheels and central axes

  

- 

We recommend having the wheels (rear 20” and front 14”) checked by a standard bicycle repair shop at least twice a 

year. For safety reasons, make sure that the wheel spokes or central axis are not loose before each use of the 
stroller/baby buggy. 
D. 

Wheel frame and mounting

  

–

 Regularly check that all nuts and bolts are tightened properly. 

E.

 Storage

 

 

–

 Store the stroller/baby buggy in a dry and well-ventilated place. Before storing, make sure that the stroller/baby buggy 

is dry; this will prevent it from becoming mouldy. If the stroller is not in use, protect it against sunshine; this will prevent 
it from discolouring. Do not store the stroller coupled to the bike. 
Check all parts of your stroller/baby buggy before each use! 

 

 

NOTICE 

 

SAFETY INSTRUCTIONS 
 

Important rules for safe use of your xRover stroller/baby buggy. 

1. Read carefully all instructions before using the stroller/baby buggy! Incorrect understanding and 
failure to follow these instructions may lead to an otherwise avoidable accident at which you and/or 
your passengers may sustain a serious or fatal injury. 
2. Safe and correct use of this product is your responsibility! Before using your stroller/baby buggy, 
take a trial bike ride, go for a walk or run or hike with the stroller loaded (to more than the expected 
weight of passengers with load) to assure that you will handle the loaded stroller/baby buggy during 
each of these activities. Be extremely careful when operating the stroller/baby buggy off roads. Apart 
from the safe ride principles, always follow the rules stated below. 
3. Make sure that your bike is in good operating condition. We recommend carrying out regular safety 
checks by a certified bicycle mechanic. 
 

NOTICE  

The colours of the covering 
and other parts of the 
stroller/baby buggy may 
change due to the weather, 
sunlight and atmospheric 
exposure! 

Содержание ROXER xRover S




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды