background image

Owner’s Manual #513685 

25 

U421 I2 Model Machines

PROBLEM

POSSIBLE CAUSE

REMEDY

Overrun too high.

1 Mix pump hose service life is 

exceeded.

1 Reposition/replace mix pump hose.

2 Out of mix.

2 Replenish mix supply.

3 Overrun setting too high.

3 Decrease overrun setting.

4 Pick-up leg of mix pump hose is 

collapsing.

4 Reposition hose. 

Replacement mix 
pump hose won’t 
feed through pump.

1 Feeding hose into discharge hole of 

mix pump cover.

1 Feed hose into suction side of cover.

2 Hose ends not cut squarely.

2 Carefully cut hose end off squarely (no tails).

3 Force feeding too quickly.

3 Gently and slowly assist feeding of hose up 

into pick-up hose side of cover.

4 Pump motor not running.

4 Press the Pump button to turn the pump On.

Air exiting mix pick-
up hose.

1 Pickup tube check valve missing.

1 Contact local Stoelting Distributor.

Dispensed product 
air “pops”

1 Overrun setting too high.

1 Decrease overrun setting.

2 Mix pump hose service life is 

exceeded.

2 Reposition/replace mix pump hose.

3 Overdrawing the machine’s capacity. 3 Reduce dispense rate.
4 Recent low mix condition.

4 Open spigot fully and allow excess air to 

escape.

Mix leakage from 
pump.

CAUTION: To prevent mix pump damage from dried mix deposits, immediately 
disassemble and clean pump.

1 Mix pump hose service life is 

exceeded.

1 Remove mix pump hose. Disconnect pump 

from power source. Remove mix pump cover/

clamp. Clean the rollers a small amount of 

soapy water. Clean mix from pump. See 

Section 4.2 for hose replacement.

Pump is noisy/
squeaking.

Note: The action of the air compressor rocking arm creates a repetitive clicking sound during 

operation. This is normal. 

Note: The peristaltic mix pump has three squeeze rollers that use self lubricating bearings. 

If squeaking exists with the mix pump hose in place and stops with the hose removed, the 

squeeze roller bearings can be lubricated using a silicone based spray. Remove the mix 

pump hose. Disconnect pump from electrical power. Remove four cover/clamp thumbscrews. 

Remove entire cover/clamp as one unit. Spray silicone based lubricant on each end of each 

squeeze roller. Spin rollers to work lubricant into bearings. Repeat as needed. 

Caution: Do not use cleaning/dissolving type lubricants like wd-40. These lubricants 
are not bearing friendly and will accelerate bearing wear.

Mix in air hoses.

1 Air/mix tee above black cover/clamp. 1 Air/mix tee must be below black cover/clamp.
2 Air leak.

2 Check stainless steel tube connection. Tighten 

all hose clamps.

3 Mix hose on wrong air/mix tee 

fi

 tting. 3 Refer to diagram for correct hose connections.

Содержание Stoelting U421 I2






































Отзывы: