background image

SFWARR-013 

Revision 04 

Page 1 of 1 

 

 
 

DOMESTIC WARRANTY 

(Including Mexico) 

SOFT SERVE / SHAKE EQUIPMENT 

 
1. 

Scope

 

PW  Stoelting,  L.L.C. 

(“Stoelting”)  warrants  to  the  first  user  (the  “Buyer”)  that  the  freezing  cylinders, 

hoppers,  compressors,  drive  motors,  speed  reducers,  and  augers  of  Stoelting  soft  serve  /  shake 
equipment  will  be  free  from  defects  in  materials  and  workmanship  under  normal  use  and  proper 
maintenance  appearing  within  five  (5)  years,  and  that  all  other  components  of  such  equipment 
manufactured  by  Stoelting  will  be  free  from  defects  in  material  and  workmanship  under  normal  use 
and  proper  maintenance  appearing  within  twelve  (12)  months  after  the  date  that  such  equipment  is 
originally installed.  

 
2. 

Disclaimer of Other Warranties

 
 

THIS  WARRANTY  IS  EXCLUSIVE;  AND  STOELTING  HEREBY  DISCLAIMS  ANY 
IMPLIED  WARRANTY  OF  MERCHANTABILITY  OR  FITNESS  FOR  PARTICULAR 
PURPOSE. 

 
3. 

Remedies

 

Stoelting

’s sole obligations, and Buyer’s sole remedies, for any breach of this warranty shall be the 

repair  or  (at  Stoelting’s  option)  replacement  of  the  affected  component  at  Stoelting’s  plant  in  Kiel, 
Wisconsin,  or  (again,  at  Stoelting

’s  option)  refund  of  the  purchase  price  of  the  affected  equipment, 

and,  during  the  first  twelve  (12)  months  of  the  warranty  period,  deinstallation/reinstallation  of  the 
affected  component  from/into  the  equipment.  Those  obligations/remedies  are  subject  to  the 
conditions  that  Buyer  (a)  signs  and  returns  to  Stoelting,  upon  installation,  the  Start-Up  and  Training 
Checklist for the affected equipment, (b) gives  Stoelting prompt written notice of any claimed breach 
of warranty within the applicable warranty period, and (c) delivers the affected equipment to Stoelting 
or its designated service location, in its original packaging/crating, also within that period. Buyer shall 
bear the cost and risk of shipping to and from Stoelting’s plant or designated service location. 

 
4. 

Exclusions and Limitations

 

This warranty does not extend to parts, sometimes called “wear parts”, which are generally expected 
to  deteriorate  and  to  require  replacement  as  equipment  is  used,  including  as  examples  but  not 
intended to be limited to o-rings, auger flights, auger seals, auger support bushings, and drive belts. 
All such parts are sold  

 

AS IS. 

 
 

Further, Stoelting shall not be responsible to provide any remedy under this warranty with respect to 
any component that fails by reason of negligence, abnormal use, misuse or abuse, use with parts or 
equipment not manufactured or supplied by Stoelting, or damage in transit. 

 
 

THE REMEDIES SET FORTH IN THIS WARRANTY SHALL BE THE SOLE LIABILITY 
STOELTING  AND  THE  EXCLUSIVE  REMEDY  OF  BUYER  WITH  RESPECT  TO 
EQUIPMENT  SUPPLIED  BY  STOELTING;  AND  IN  NO  EVENT  SHALL  STOELTING 
BE  LIABLE  FOR  ANY  INCIDENTAL  OR  CONSEQUENTIAL  DAMAGES,  WHETHER 
FOR BREACH OF WARRANTY OR OTHER CONTRACT BREACH, NEGLIGENCE OR 
OTHER TORT, OR ON ANY STRICT LIABILITY THEORY. 

Содержание Stoelting U421 I2






































Отзывы: