background image

1

USERS INSTRUCTIONS

1.1 GAS APPLIANCES

Gas Safety (Installation and Use) Regulation (UK).

In the interests of your safety and that of others it is a legal 
requirement that all gas appliances are installed and correctly 
maintained by a competent person and in accordance with the 
latest regulations.

1.2 ELECTRICAL SUPPLY

Please ensure that this appliance has been properly connected 
to the electrical supply by means of a double pole isolator or 
un-switched socket, and that the correct size of fuse (3 AMP) 

has been itted.

Warning: this appliance must be earthed!

  

1.3 GUARANTEE REGISTRATION CARD

Please take the time to ill out your guarantee registration card. 

The completed warranty card should be posted within 30 days 
of installation.

1.4 APPLIANCE  LOG BOOK (UK only)

A logbook section can be found at the rear of the appliance 
installation booklet. This important document must be completed 
during the installation/commissioning of your boiler. All GAS 
SAFE registered installers carry a GAS SAFE ID card, and have 
a registration number. These details should be recorded in the 
Benchmark logbook section within the installation booklet. You 
can check your installers details by calling GAS SAFE direct on 
08004085500. Failure to install and commission the appliance in 
accordance with the manufacturers instructions may invalidate 
the warranty. This does not affect your statutory rights.

1.5 HOW DOES IT WORK?

Your Vision boiler supplies heated water to your radiators and 
hot water to your hot water taps. The central heating is con-
trolled via a time clock and any thermostats that your installer 

may have itted.  The boiler will light when it receives a request 

from the time clock via any thermostat that may be installed, or 
whenever a hot water outlet (tap) is opened. Your Vision boiler 
lights electronically and does not have a pilot light.
In the unlikely event of a fault developing with your boiler, the 
supply of gas to the burner will be terminated automatically.

Dear Customer

Your Vokèra Vision boiler has been designed to meet and exceed the very latest standards in gas central heating technology, 

and if cared for, will give years of reliable use and eficiency.  

Please therefore take some time to read these instructions carefully.

Do’s and Don’t’s

Do

 ensure that the system pressure is periodically checked

Do

 ensure that the boiler should not be used by children or unassisted disabled people

Do

 ensure that you know how to isolate the appliance in an emergency

Do

 ensure that you are familiar with the appliance controls

Do

 ensure that your installer has completed the appliance log book section

Do not

 attempt to remove the appliance casing or gain internal access

Do not

 hang clothes etc. over the appliance

Do not

 forget to have the appliance serviced annually.

This booklet is an integral part of the appliance. It is therefore necessary to ensure that the booklet is handed to the person re-
sponsible for the property in which the appliance is located/installed. A replacement copy can be obtained from Vokèra customer 
services.

INTRODUCTION

1.6 DIMENSIONS

1.7 CLEARANCES REQUIRED

ABOVE 150 mm
BELOW 150 

mm

LEFT SIDE 

12 mm

RIGHT SIDE 

12 mm

FRONT 600 

mm

  Vision 25C - 30C

  HEIGHT 

715 mm 

  WIDTH 

405 mm 

  DEPTH 

248 mm 

1.8 FROST PROTECTION SYSTEM

The Vision  is equipped with a built-in frost protection system, 
this enables the boiler to over-ride the time controls – even if 
switched off – and operate the burner and/or pump, should 
the temperature drop below 5

0

C for the main and for the DHW 

line. In particular the burner will be in ON status until the main 
temperature reaches 35°C for CH appliance and 55°C for 
DHW appliance.

 

Please note that the frost protection system 

is designed to protect the appliance only, should frost protec-
tion be required for the heating system, additional controls 
may be required.

NOTE

The frost protection system is reliant on the appliance having a 
permanent electrical supply, and being in a non-fault condition.

1.9 APPLIANCE STATUS INDICATORS

Your boiler is equipped with a large LCD display that indicates 
the appliance operating status. 

1. THINGS YOU SHOULD KNOW

Содержание Vision C









































Отзывы: