background image

16

Fig. 19

Mains (230V) 

terminal block

Fig. 17

Fig. 18

A

top connections capped off, however these can be re-
moved to allow pipe work confi gurations as detailed in 3.11.
Depending on system requirements, it may necessary 
to increase the size of the fl ow & return pipe work after 
the service connections. 

4.6.3 CONDENSE PIPE

During normal operation the boiler produces condense 
which is collected in a trap located in the lower part of 
the boiler. A fl exible pipe (condense outlet pipe) is con-
nected to the outlet of the trap. The fl exible pipe must be 
connected to a plastic waste pipe only. The plastic waste 
pipe must have a minimum of a 3º fall towards the drain. 
Any external run of pipe should be insulated to prevent 
the risk of freezing.  

CONNECTING THE CONDENSATE OUTLET

Gently pull the condense outlet pipe down from its location 
inside the boiler until approximately 100mm protrudes 
from the underside of the boiler. Connect a suitable plastic 
(not copper) pipe (no less than 20mm diameter) to the 
outlet pipe and ensure it discharges in accordance with 
building regulations or other rules in force.

4.7 ELECTRICAL CONNECTIONS

The electrical supply must be as specifi ed in section 
3/3A. A qualifi ed electrician should connect the electrical 
supply to the appliance. If controls – external to the appli-
ance – are required, a competent person must undertake 
the design of any external electrical circuits, please refer 
to section 8 for detailed instructions. ANY EXTERNAL 
CONTROL OR WIRING MUST BE SERVED FROM THE 
SAME ISOLATOR AS THAT OF THE APPLIANCE. The 
supply cable from the isolator to the appliance must be 
3-core fl exible sized 0.75mm to BS 6500 or equivalent. 
Wiring to the appliance must be rated for operation in 
contact with surfaces up to 90°C.

4.7.1 CASING REMOVAL (fi g. 17)

To gain internal access to the appliance you must fi rst 
remove the casing, proceed as outlined below:

  Locate and remove the 4-elongated nuts at corner 

of the on the casing 

 

using a screwdriver or suitable 

spanner/socket.

  Draw the casing forwards to disengage it from the 

locating studs and then remove.



Store the casing and nuts safely until required.  Re-fi t 
in the reverse order.

WARNING

The casing forms the ‘room-sealed’ element of the appli-
ance; therefore you must ensure that the seal is in a good 
condition, that the casing is correctly located, and that 
all 4-nuts are correctly fi tted and tightened to ensure the 
necessary seal to allow safe operation of the appliance.

4.7.2 APPLIANCE TERMINAL BLOCK

The appliance terminal block is located on the rear of the 
control fascia. Remove the casing as described in 4.7.1. 
Locate and remove the two screws from the control panel 
(fi g. 18). Gently pull the control panel forwards and down. 
Locate the terminal block cover (see fi g. 19).

NOTE

The appliance comes with a factory fi tted link-wire (‘TA’) 
and supply fl ex to allow basic operation of the boiler once 
the circulating pump has been connected. If it is anticipated 
that external controls will be required please refer to the 
wiring diagrams in section 8 for more detailed information.

Содержание MYNUTE 15 VHE











































Отзывы: