Vogtlin SmartTrak 100 Series Скачать руководство пользователя страница 5

Страница: 5 / 114

CHAPTER 1: INTRODUCTION

Welcome to the future of gas flow measurement!

This manual is your guide to SmartTrak. Visit the Vögtlin Instruments website

www.vogtlin.com

any time for more information about this product.

The SmartTrak instruments offer a variety of features for ease of operation. Among these
features:



Dial-A-Gas

allows a user to change from among 10 gases while maintaining

accuracy.



The Optional Pilot Module:

control electronics that offers both display and control

options at the user’s fingertips.



Digital Electronics

: maximum performance with minimum noise plus exceptional

tuning capability.



Choice of

Analog Communications Options and RS-232

with every SmartTrak

instrument.



Flexible Design

with many functions that can be re-configured on-site by the user.



Compact Footprint

that allows SmartTrak to fit almost anywhere.



Wide range of sizes

for gas flow from 0.1 mln/min to 1000 ln/min.



And many more

Using This Manual

This manual is organized into six chapters:



Chapter 1:

Introduction and Theory of Operation.



Chapter 2:

Installation, Plumbing & Wiring instructions.



Chapter 3

: Analog Operation.



Chapter 4

: Digital Operation with the Optional Pilot Module.



Chapter 5

: Digital Operation with RS-232 & SmartTrak Software.



Chapter 6

: Technical Support and Service.



Appendix A,B,C,D,E,F,G,H,I,J

Throughout this manual, we use the word

instrument

as a generic term to represent all

models of Vögtlin Instruments’

SmartTrak Series 100

mass flow meters and

controllers.

Содержание SmartTrak 100 Series



















































































































Результаты поиска

Содержание SmartTrak 100 Series

Отзывы:

Бренды по названию

Популярные бренды

Vogtlin SmartTrak 100 Series, Руководство пользователя

Результаты поиска

Содержание SmartTrak 100 Series

Отзывы:

Бренды по названию

Популярные бренды