manualshive.com logo in svg

Vogtlin SmartTrak 100 Series, Руководство пользователя

Поделиться
Скачать
Vogtlin SmartTrak 100 Series Скачать руководство пользователя страница 19

19 

 

 

 
 
 

 
 

 

 

 

NOTE: Pins 1, 3, and 10 are connected 
together inside the instrument. Do not tie these 
grounds together outside the instrument. Must 
have one connection per analog ground. 
Recommended use listed. 

 
 
 

Instrument Power: 

The SmartTrak requires a 15-24 VDC power supply. If you are using the power supply 
supplied by Vögtlin, connect it to the 15-pin HD DB-15 connector on the side of the 
instrument. If you are supplying your own power source, it must be a regulated 15-24 VDC 
with ripple not to exceed 100 mV peak-to-peak. It must be capable of producing the current 
specified for the appropriate voltage shown in Figure 2-5: Power Supply Requirements. 
Apply power as follows: positive (+) to the green (pin 6) and negative (-) to the yellow (pin 
5) wires. The instrument is polarity sensitive. If you reverse this wiring, the instrument will 
not be damaged, but it will not function. 

 

Instrument Grounding: 

The SmartTrak has very high levels of RFI and EMI shielding built into the metal electronics 
cover (meets or exceeds the CE Standard EN 61326-1; 2006). To maintain the integrity of 
this CE rating, it is critical that a path be provided for any residual internal noise to exit the 
instrument or it may register on the outputs. Grounding provides this path. 

 

To properly ground your instrument, secure the chassis to solid earth ground using the 
mounting holes on the bottom of the flow body. If the instrument will be used without 
permanent mounting (on a laboratory bench, for instance) then, using the provided cable, 
connect the shield wire (no insulation) to earth ground in your facility. If you purchased a 
Vögtlin power supply, a ground wire is provided for your convenience. 

 

Figure 2-5: Power Supply Requirements 

Instrument Type 

Recommended Input 

Voltage 

Minimum Current 

Required (mA) 

M100L Meter 

15-24 VDC (+ 10%) 

230 

M100M Meter 

15-24 VDC (+ 10%) 

230 

M100H Meter 

15-24 VDC (+ 10%) 

230 

C100L Controller 

24 + 10% VDC 

500 

C100M Controller 

24 + 10% VDC 

800 

C100H Controller 

24 + 10% VDC 

1260 

NOTE: 

The Compod™ adds an additional 100mA to the ST2 current ratings

.

 

Содержание SmartTrak 100 Series



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды