manualshive.com logo in svg

Vogtlin SmartTrak 100 Series, Руководство пользователя

Поделиться
Скачать
Vogtlin SmartTrak 100 Series Скачать руководство пользователя страница 12

12 

 

 

 
 
 
 
 
 
 
 
 
 

Pre-Installation Check List 

1.

 

Double-check to be sure that the O-ring material used in your instrument is 
compatible with the gas to be measured. 

The O-ring material used in your 

SmartTrak can be found in the Data Label. See Appendix A for a table of elastomer 
compatibility with a wide variety of gases. 

 

2.

 

Vögtlin strongly recommends you install an in-line filter upstream of the 
instrument. 

Recommended filter size: 10 micron. A 10 micron filter is available 

from Vögtlin as an accessory. See Appendix B or contact your local Vögtlin 
distributor. 

 

3.

 

Do not locate the instrument in areas subject to sudden temperature changes, 
excessive moisture or near equipment radiating significant amounts of heat. 

Be sure to allow adequate space for cable connectors and  wiring. 

 

4.

 

For controllers, use a properly sized pressure regulator. 

Make sure the pressure 

regulator is not too small or too big. There can be no restrictions (such as valves, 
tubing or pipe internal diameters, reducers, etc.) upstream or downstream of the 
controller with a dimension that is less than the valve orifice diameter. To 
determine orifice diameter, consult the calibration certificate included with your 
instrument. If restricted, controller will not reach full scale. 

 

5.

 

Output Signals: 

The SmartTrak has two analog outputs that are linearly 

proportional to the gas mass flow rate, one voltage and one current. Choose from 0- 
20 mA or 0/0/4-20 mA for current plus one voltage signal: 0-5 VDC or 0-10 VDC 
or 1-5 VDC. The output signals specified at time of order will be indicated on the 
data label.  You may change among the current and the voltage output signal at 
your discretion after receipt of the instrument using the Pilot Module or the 
SmartTrak Software (see Chapters 4 & 5). Changing the output signals has no 
influence on the instrument’s accuracy. 

 

NOTE: For the SmarTrak 100 plus Compod, the 0-5 VDC I/O cannot be used. Only 
0/4-20 mA I/O is available. 

 

6.

 

The CAT-5 

connector on the side of the SmartTrak is NOT an Ethernet connector. 

It is for use with the optional Remote Pilot Module. Do not plug an Ethernet cable 
here as damage may result. Keep this connector covered if possible whenever it is 
not in use. 

Содержание SmartTrak 100 Series



















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды