-6-
ASSEMBLY INSTRUCTIONS
OPTIONAL BLOWER ATTACHMENT (NOT INCLUDED
WITH STOVE)
1.
Attach blower assembly (fig.4) to back of rear
deflector. (fig.5)
NOTE: Make sure ceramic gasket is positioned between
rear deflector heat shield and blower assembly. Use four
screws provided to fasten the blower to rear heat shield.
2.
Route the power cord away from the stove. Do
not allow the power cord to touch ay hot surfaces.
Keep power cord at least 12” from stove surfaces.
3. Once the stove is positioned, plug the power cord
into a grounded 120v outlet.
FIREBRICK ASSEMBLY
Firebrick extends the life of your stove and radiates heat more evenly. Check to see that all firebricks are in their
correct positions and have not become misaligned during shipping or assembly. If removed for ease of locating
stove, firebrick and ash dump cover must be replaced before firing. See diagrams, for proper positioning.
CAUTION: Never operate stove with missing or cracked fire bricks!
TR001B | 20120125.1
www.vogelzang.com
DEFENDER™
|
Page 5
ASSEMBLY INSTRUCTIONS
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
1. Uncrate the stove and remove all packing materials
and protective poly bag.
NOTICE: DO NOT remove ceramic blanket
material
from inside stove pipe opening (Fig. 1).
This blanket provides an air seal on the side walls
of the stove to direct combustion gasses over the
secondary combustion tubes before exiting via the
chimney.
DO NOT REMOVE the ceramic blanket
or your stove will not operate properly.
ing. There are six different sizes brick and two with
notches. Note the location of each while removing
or refer to fig. 9a, b & c (page 6) for proper location
inside firebox.
Fig. 4 – Optional
Blower Assembly
position and secure using the nuts removed in
step #4. Tighten nuts securely.
6. Next install the Ash Drawer Supports to the
threaded weldments on the bottom of the stove,
fig. 3. Each support uses three threaded bolts as
shown.
7. Carefully lift the stove into an upright position.
OPTIONAL BLOWER ATTACHMENT
(NOT INCLUDED WITH STOVE)
Figure 1 – DO NOT remove ceramic blanket from
inside stove pipe opening. This is NOT packing
material but an integral component of the stove
combustion system.
2. Remove all parts from inside stove. NOTE: Stove
may be lightened during installation by removing
fire brick. Replace firebrick & ash cover before us-
Fig. 2– Attach (4)
Legs
DO NOT
REMOVE!
3. Place flattened
carton on floor
and lay the stove
on it’s back.
4. Remove the four
9/16” nuts from
t h e t h r e a d e d
studs located on
each corner.
5. Place legs in
1. Attach blower assembly
(fig. 4) to back of rear
deflector. (fig.5)
NOTE: Make sure ce-
ramic gasket is posi-
tioned between rear de-
flector heat shield and
blower assembly. Use
four screws provided to
fasten the blower to rear
heat shield.
continued on next page
Fig. 3 – Attach
Ash Drawer
or equivalent)
tools
• Pencil
• 6 foot Folding Rule or Tape Measure
• Tin Snips
• Drill: Hand or Electric
• 1/8” dia. Drill Bit (for sheet metal screws)
• Screwdrivers (blade and Phillips type)
• 9/16” Nut Driver or Ratchet with 9/16” Socket
• Safety Glasses
• Gloves
materials
(NOTE: The following items are NOT included with
your stove and are required for proper installation.)
Flooring Protection as specified (see page 6)
Chimney Connection: 6”/152mm dia. minimum 24 MSG black or
26 MSG blue steel straight stove pipe or elbow(s).
1/2”/13mm Sheet Metal Screws
Chimney: Existing 6˝ Code-approved Lined Masonry Chimney
or 6˝ Inside Dia. UL 103 HT (US)/ULC-S629 (CDN) listed
manufactured chimney.
Furnace Cement (manufacturer recommends Rutland Code 78
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of your wood
stove and assumes no responsibility of any incidental or consequential damages.
Содержание TR001B
Страница 25: ... 25 NOTES ...
Страница 26: ...NOTES ...
